set motor_pwm_rate to some value > 500 (1000, 8000, 16000 etc works on my scope).
then the motor output can be used to directly drive brushed motor fets.
PWM is rescaled to 0-base in brushed mode, so all same values of min/maxthrottle apply.
* Proper initialization sequence framework for various supported GPS types. NMEA will now auto-detect its baud rate based on received frames.
* As a result of the above, gps_baudrate has been changed to enum, to only allow fixed rates. (GPS baudrate, -1: autodetect (NMEA only), 0: 115200, 1: 57600, 2: 38400, 3: 19200, 4: 9600)
* UBX binary initialization at any specified baudrate with auto-reconnect on signal loss.
* GPS thread to handle initialization, signal loss and configuration. No longer does GPS need to be powered before FC, and on GPS reconnect, it will be re-initialized if needed.
MTK NMEA/binary initialization is omitted for now, as I can't find my MTK GPS
GPS deltaTime can be calculated to display update rate.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@438 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
First cut at polymorphic serial port implementation. Split serialPort_t into uartPort_t and serialPort_t. Calls to uartWrite() can now be replaced with calls to serialWrite().
Replacing calls to serialWriteByte(softSerial_t*, char) with calls to serialWrite(serialPort_t*, char). This completes the proof of concept for polymorphic serial port implementations (uartPort and softSerialPort).
Renaming isSerialAvailable to uartTotalBytesWaiting. Renaming serialAvailable to softSerialTotalBytesWaiting. Adding serialTotalBytesWaiting to serial API and updating calls to the former methods to use the serial API.
Renaming serialRead to softSerialRead. Adding serialRead to serial API and updating calls to uartRead and softSerialRead to use the serial API. Renamed uartPrint to serialPrint which now works on any serialPort implementation.
Replacing calls to isUartTransmitEmpty with isSoftSerialTransmitBufferEmpty. Replacing remaing calls to uartWrite with serialWrite. Adding isSoftSerialTransmitBufferEmpty to the serial API. Adding serialSet/GetBaudRate to the serial API. Since softSerial does not implement serialSetBaudRate some GPS serial initialisation code has been updated.
At this point it is probably possible to switch around all the ports and use a software serial implementation if desired.
By Dominic Clifton / https://github.com/hydra/baseflight/
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@423 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
FEATURE_SPEKTRUM has been removed and replaced with FEATURE_SERIALRX.
cli option serialrx_type now configures what type of receiver it is
0 = spektrum1024, 1 = spektrum2048, 2 = sbus
sbus will need hardware inverter to use.
also cleaned up receiver drivers to assign readrawRC callback instead of assigning in code in main()
none of this has been tested.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@418 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added and began work on integrating failsafe_detect_threshold
got rid of acc_lpf_for_velocity since that seemed no longer used.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@317 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
PWM and ADC configuration is the same as the naze32 for now. Requires an accelerometer is connected via I2C2.
I2C signals SDA2 and SCL2 are on the UEXT header (Pins 6 and 5 respectively)
USART signals TX and RX are on the CON3/CON4 headers (TX = D7, RX = D8)
Onboard LEDs (LED1/LED2) working.
Buzzer support removed for now as it conflicted with PWM map and LEDs.
mma845x support disabled as it conflicted with an LED.
Relocated some NAZE specific comments.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@302 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
mw2.2-merged stuff:
* implemented profiles 0-2 (called 'setting' in mwiigui)
* merged in MSP changes including profile switch
* cleaned up rc / aux switch stuff in mw.c based on 2.2 rewrite
* main loop switch for baro/sonar shit adjusted
todo: basically the rest of 2.2 changes (i think some minor imu/gps/baro updates)
baseflight-specific stuff:
* made boxitems transmission dynamic, based on enabled features. no more GPS / camstab trash if it's not enabled
* cleaned up gyro drivers to return scale factor to imu code
* set gyro_lpf now controls every supported gyro - not all take same values, see driver files for allowed ranges, in case of invalid lpf, defaults to something reasonable (around 30-40hz)
maybe couple other things I forgot. this is all 100% experimental, untested, and not even flown. thats why there's no hex.
merge is still ongoing.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@294 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
fixed pwm init for airplane mode mistakenly deleting motors from the mix. flyingwing should really work now.
removed led debug from althold
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@223 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
I heard thats not a problem since tarduino only allows 4RC+2AUX channels anyway! If you want more, upgrade to PPM.
So you use RC3/4 for GPS, and connect the rest of the channels as usual. Channels used for GPS uart are
skipped, so no changes to 'map' are necessary. Simply connect in order.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@212 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
synced angle/horizon mode stuff from mwc. no idea what it does.
perhaps the most important part of this update:
-errorAngle = constrain(2 * rcCommand[axis] - GPS_angle[axis], -500, +500) - angle[axis] + cfg.angleTrim[axis];
+errorAngle = constrain(2 * rcCommand[axis] + GPS_angle[axis], -500, +500) - angle[axis] + cfg.angleTrim[axis];
(which means GPS might actually work).
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@209 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added ms5611 driver
refactored pressure sensor subsystem to allow multiple sensors
couple changes in PWM driver to make motor/servo arrangement for airplane mode more intuitive
moved MAX_MOTORS/MAX_SERVOS etc into drv_pwm.h
staring to merge back in airplane/flyingwing mixes
fix for tri servo display - mwc moved it to servo[5] again, gui was broken, function not.
will probably implement custom mixer soon (motors only, no servos)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@198 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
this has been hover-tested.
all current functionality *should* work even though the driver has been rewritten.
please test carefully, especially servo configurations!
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@197 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
removed camtrig stuff since it wasnt possible. somewhat replaced with aux forwarding (see below)
2.1 buzzer code changed, untested.
removed flying wing mixer. nobody used that.
added alt_hold_throttle_neutral, nav_slew_rate and looptime configuration to cli. default looptime set to 3000. changed default gyro_cmpf to 400 to sync with 2.1.
increased bmp085 oversampling
added gimbal_flags (bit 4 set) flag which, in PPM mode, forwards AUX1..4 to the lower 4 PWM outputs instead of using them as motors. set gimbal_flags=8 to test it out. output is fixed to 50Hz.
merged 2.1 gps changes (not many)
casting in gyro smoothing (nobody uses that anyway)
calibrate accel in gimbal mode, set smallangle in gyro-only mode
vtail4 mixer fix
flight tested on quadx w/ppm.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@182 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added fifo mode to adxl345 driver, currently disabled. work in progress.
fixed output for PWM 5-8 when used with PPM + camstab + abovequad configs.
fixed baro, now alt-hold actually works. silly copypaste typo.
trashed all remaining parts of power meter and lcd configuration stuff. useless.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@145 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
removed feature digital_servo since its now set by cli instead.
added proper tx end check into uart, to remove delay inside printing out set values and tx buffer overrun during help()
instead of passing a bunch of params to pwm driver, made a config struct
fixed a bug in gps baudrate
fixed typo in stmloader.c
whitespace / indentation cleanups in various drivers
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@137 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
renamed gcc startup file to .S (breaks some lunix dudes apparently)
ppm sum handler waws hardcoded to TIM2 instead of using passed parameter. fixed. (thanks sbaron)
invalid data from pwm/ppm read are returned as midrc, not 1500. (robert_b)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@133 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
split uart2 initialization inside drv_uart. added receive data callback to use either with GPS or spektrum satellite
added spektrum satellite support, also freeing up 4 motor outputs for hexa/octo/camstab
configurable acc lpf and gyro lpf via cli
configurable (build-time) temperature lpf on baro. seems mostly useless.
fixed a nice boner bug in mag code which ended up multiplying magADC twice with magCal data.
fixed mpu3050 driver to allow configurable lpf, also broke other stuff in the process. considering moving this sort of stuff to "init" struct for sensor.
pwm driver rewritten to fully disable pwm/ppm inputs (such as using spektrum satellite case)
cleaned up double math in gps.c to use sinf/cosf etc
removed TRUSTED_ACCZ since its useless anyway
whitespace cleanup
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@130 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added (untested) support for additional PWM output channels incase of PPM input - 4 more, so total of 10 outputs in this mode.
added (mostly untested) support for throttle calibration - short out PPM input connector with a bind plug and power up.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@122 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
implemented battery cell count auto detect (DJI, you can steal this source from me for your next product). automatically finds 2S..6S battery, and sets warning voltage accordingly
added new battery config -related stuff in cli, min/max cell voltage for non-lipo users. Defaults for lipo are 4.3V/cell (max) and 3.3V/cell (min).
added pid setting stuff into cli from nicodh
added 'status' command to cli to print out system info.
added build date/time to 'version' in cli, to track down stupid users.
config version bumped, settings are cleared again.
refactored battery voltage stuff a bit, and got rid of 3 levels of warnings. don't see any benefit at all.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@121 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added 'reset to defaults' to cli
got rid of 'servo' feature since that's not really a feature a user can set
added couple more configurable tricopter things to config struct.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@118 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
changed gyro/acc to allow different drivers without recompile, this allowed adding mpu6050 support w/autodetect
moved sensor orientation code into driver - each driver provides its own
added support for mpu6050 - desolder mpu3050 and adxl345, replace with mpu6050 for instant ???
merged multiwii 2.0pre3 code changes (none that mattered except mag calibration and typo in baro stuff)
changes to sensor autodetect for new dynamic drivers
more of ledring stuff done (still doesn't work, so dont try)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@115 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
