own dedicated serial port.
Added a feature to enable/disable RX_MSP.
Renamed feature SERIALRX to RX_SERIAL.
Renamed feature PARALLEL_PWM to RX_PARALLEL_PWM
Renamed PPM to RX_PPM.
Update serial configuration checking to better support Serial RX and
telemetry by verifiying serial port features and supported baud rates.
It's now possible to use a low-speed serial rx provider via softserial -
only problem is all the current serial rx providers are 100000/115200
baud. The code changes however open the door for using serial rx and
any capable serial port such as uart3-5 on the STM32F30x
It's also now possible to use GPS at low speeds on software serial
ports.
match the comment from pullrequest about spacing
remains : some hand alignment for comment and wrong /** */ usage.
Conflicts:
src/board.h
src/buzzer.c
src/config.c
src/drivers/serial_common.h
src/drivers/system_common.c
src/drv_gpio.h
src/drv_pwm.c
src/drv_timer.c
src/drv_uart.c
src/flight_imu.c
src/mw.c
src/serial_cli.c
This is a large commit, from the commit it is clear that the mixer has
many dependencies, this is expected since it is central to the
application.
To achieve the decoupling many master config and profile members had to
be moved into structures.
Relocated throttle/pitch curves into rc_curves.c/h since it has nothing
to with rx code, this fixed the dependencies inside the rx provider
files.
Rename yawdeadband to yaw_deadband to match other variables/cli
commands.
Fix a couple of usages of MAX_MOTORS where MAX_SUPPORTED_MOTORS should
be used instead.
In doing so accelerometer sensor and trim code had to be cleaned.
Added a new method to buzzer.c to avoid exposing toggleBeep.
Renamed current_profile to current_profile_index to avoid confusion.
Moved some GPS code from mw.c into gps_common.c.
Moved pid values into a pidProfile_t structure; this was done so that
gps_common.c does not have a dependency on config_profile.h.
pidProfile_t lives in flight_common.h now.
Moved gps profile settings from profile_t into gpsProfile_t for the same
reason.
Removed gps_common.c's dependency on masterConfig_t by passing needed
variables into gpsInit().
separate concerns and help reduce and clarify dependencies.
cfg and mcfg are too similarly named and are not obvious. Renamed cfg
to currentProfile and mcfg to masterConfig. This will increase source
code line length somewhat but that's ok; lines of code doing too much
are now easier to spot.
only what it's name implies and it's method takes no arguments. This
avoids the 0/1 magic numbers which was a flag to decide whether the user
should be notified after the EEPROM has been read (!).
Introduced a method called readEEPROMAndNotify() which is used in all
cases where writeEEPROM(1) was previously called.
Additionally this avoid re-reading the profile when the reboot command
is issued which speeds up reboots.
Finally this avoid needless comments because the code tells you now what
it is going to do.
serial_common.c/h. decouple runtime_config from serial ports. decouple
buzzer from serial ports. decouple opening of the main serial port from
the msp code. decouple serial rx providers from runtime_config. rename
core_t to serialPorts_t since it only contained serial ports. It's now
clear which files use serial ports based on the header files they
include.
of determining a revision code. Previously there was mpu6050 specific
code in cli.c (the status command).
Finally this commit has removed all non-serial port configuration
settings from core_t so that a future commit can refactor core_t to
reduce dependencies on serial port code.
In doing this I also noted from other source code that the MPU6050
accelerometer trim for some revisions appeared to be incorrectly set to
255 * 8 instead of 256 * 8.
channels when using Spektrum 2048 - untested. Renamed and extracted
core_t.numRCChannels to rxConfig.channelCount so that future commits can
clean up core_t further since core_t contains completely unrelated
properties.
code into rx_common.c. Moved some GPS code into gps_common.c. Isolated
some GPS functions into gps_common.c that were called from mw.c/loop().
moved gimbal defines into gimbal.h. Moved sound & light code into
statusindicator.c
remove dependency on board.h and mw.h on a few files.
Moved rx configuration paramaters into rxConfig in order to remove the
dependency on config_t from the sbus rx code - sumd/spektrum to follow.
Avoided use of YAW/PITCH/ROLL in some files since those constants are
from an unrelated enum type.
Replaced some magic numbers with constants to remove comments and
improve code readability.
Note, due to the tight coupling and global variable usage it was
difficult to create a smaller commit.
This fixes a bug where buzzerFreq could be uninitialised before it's
use.
This improves performance by only checking whether to sound the battery
alarm after the battery voltage has been recalculated.
There were unused battery beep codes which have been deleted to save
code size.
Configuration structure extracted from mw.h into config.h.
Moved mixer configuration structures into flight_mixer.h.
Added a build_config.c in order to decouple pwm_common.h from config.h.
Finally, battery configuration values now live in a batteryConfig
structure which means that battery.c does not depend on config.h and all
of it's dependencies.
Fixed the use of plurals on defines that were not collection objects.
PIDITEMS and CHECKBOXITEMS are now PID_ITEM_COUNT and
CHECKBOX_ITEM_COUNT.
clear what all gpio/ledring drivers need to compile and what was
unnecessarily included before.
In attempting this it was clear that ledring had a dependency on the
multiwii code, this was removed by passing the led status update method
the values it needs.
It also turned out that the ROLL/PITCH defines were coming from
rc_alias_e and much unrelated code is coupled to these defines. This
commit also includes some cleanups relating to that problem.
