synced angle/horizon mode stuff from mwc. no idea what it does.
perhaps the most important part of this update:
-errorAngle = constrain(2 * rcCommand[axis] - GPS_angle[axis], -500, +500) - angle[axis] + cfg.angleTrim[axis];
+errorAngle = constrain(2 * rcCommand[axis] + GPS_angle[axis], -500, +500) - angle[axis] + cfg.angleTrim[axis];
(which means GPS might actually work).
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@209 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
removed camtrig stuff since it wasnt possible. somewhat replaced with aux forwarding (see below)
2.1 buzzer code changed, untested.
removed flying wing mixer. nobody used that.
added alt_hold_throttle_neutral, nav_slew_rate and looptime configuration to cli. default looptime set to 3000. changed default gyro_cmpf to 400 to sync with 2.1.
increased bmp085 oversampling
added gimbal_flags (bit 4 set) flag which, in PPM mode, forwards AUX1..4 to the lower 4 PWM outputs instead of using them as motors. set gimbal_flags=8 to test it out. output is fixed to 50Hz.
merged 2.1 gps changes (not many)
casting in gyro smoothing (nobody uses that anyway)
calibrate accel in gimbal mode, set smallangle in gyro-only mode
vtail4 mixer fix
flight tested on quadx w/ppm.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@182 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added a modifier for set (type "set *") to see min/max values for each parameter. this is for gui stuff
bumped config VERSION
fixed 0xffff - now stuff in drv_pwm, after it was mentioned to me for the 3rd time :p
replaced some uint8_t -> uint32_t for loop counters - saving 4 to 8 bytes of flash each time. thanks goes to thee 35+ years of C experience kicad guy.
turned bitfiends into a regular struct - instant 100byte flash size reduction
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@174 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
feature TELEMETRY to enable it. when armed, telemetry is sent out the TX pin. It must be connected to 'Rx' pin of FrSky telemetry receiver via a level shifter. When disarmed, port goes back to 115200 bps for GUI.
fixed a typo in imu.c introduced by GYRO_INTERLEAVE junk.
todo: just switch serial speed instead of reinitializing everything.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@173 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
changed booleans to bitfield struct to match with 0622
no other functional changes, and not all enhancements (like boxlight) from 0622 are implemented yet
NOT flight tested, use at your own risk.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@172 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
applied mwc-dev GPS code with bits of tarducopter code by sbaron. Thanks again. Moved some of the GPS config stuff into cli - gps_lpf, min/max nav speed, nav_controls_heading. Remember I don't test any GPS functionality at all, so if this makes your quad fly towards North Korea at over 9000cm/sec, this is NOT my problem.
spacing fixes in a couple files.
trashed old serial code that was under #if 0
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@161 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
fixed spacing in ledring.c
defaulted acc_lpf to 100
correction in vtail4 mix (from multiwii_dev)
trashed more unused LOG_VALUES crap
no binary build since this is untested / non-flight-tested.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@152 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added fifo mode to adxl345 driver, currently disabled. work in progress.
fixed output for PWM 5-8 when used with PPM + camstab + abovequad configs.
fixed baro, now alt-hold actually works. silly copypaste typo.
trashed all remaining parts of power meter and lcd configuration stuff. useless.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@145 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added float-based acc lpf, acc_lpf_factor values now changed, its 1/factor now, values 60+ and larger filter heavier.
playing with release MPU6050 hardware, looks like acc1G is fucked, as predicted
bug in serial output (forgot to output armed bit to GUI, estalt is /10)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@144 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
took out leftovers of old dynamic mixer binary protocol - now cli sets it.
added some mpu6050 DMP stuff - all disabled by default, only for testing stuff. ignore it.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@128 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
changed gyro/acc to allow different drivers without recompile, this allowed adding mpu6050 support w/autodetect
moved sensor orientation code into driver - each driver provides its own
added support for mpu6050 - desolder mpu3050 and adxl345, replace with mpu6050 for instant ???
merged multiwii 2.0pre3 code changes (none that mattered except mag calibration and typo in baro stuff)
changes to sensor autodetect for new dynamic drivers
more of ledring stuff done (still doesn't work, so dont try)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@115 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
