match the comment from pullrequest about spacing
remains : some hand alignment for comment and wrong /** */ usage.
Conflicts:
src/board.h
src/buzzer.c
src/config.c
src/drivers/serial_common.h
src/drivers/system_common.c
src/drv_gpio.h
src/drv_pwm.c
src/drv_timer.c
src/drv_uart.c
src/flight_imu.c
src/mw.c
src/serial_cli.c
Currently port usage is hard-coded to the default port layout, cli
commands are coming in a future commit.
This decouples all code from the global 'serialPorts' structure which
has been removed. Any code that needs to use a serial port can use
findOpenSerialPort() and openSerialPort() and maintain it's own
reference to the port.
Ports can switch between functions. e.g. by default
cli/msp/telemetry/gps
passthrough all use USART1. Each port maintains it's current function.
see begin/endSerialPortFunction.
There are only certain combinations of serial port functions that are
supported, these are listed in serialPortFunctionScenario_e.
This commit also adds a few 'static' keywords to variables that should
have been.
There a a few other minor fixes and tweaks to various bits of code that
this uncovered too.
In doing so accelerometer sensor and trim code had to be cleaned.
Added a new method to buzzer.c to avoid exposing toggleBeep.
Renamed current_profile to current_profile_index to avoid confusion.
serial_common.c/h. decouple runtime_config from serial ports. decouple
buzzer from serial ports. decouple opening of the main serial port from
the msp code. decouple serial rx providers from runtime_config. rename
core_t to serialPorts_t since it only contained serial ports. It's now
clear which files use serial ports based on the header files they
include.
remove dependency on board.h and mw.h on a few files.
Moved rx configuration paramaters into rxConfig in order to remove the
dependency on config_t from the sbus rx code - sumd/spektrum to follow.
Avoided use of YAW/PITCH/ROLL in some files since those constants are
from an unrelated enum type.
Replaced some magic numbers with constants to remove comments and
improve code readability.
Note, due to the tight coupling and global variable usage it was
difficult to create a smaller commit.
This fixes a bug where buzzerFreq could be uninitialised before it's
use.
This improves performance by only checking whether to sound the battery
alarm after the battery voltage has been recalculated.
There were unused battery beep codes which have been deleted to save
code size.
Configuration structure extracted from mw.h into config.h.
Moved mixer configuration structures into flight_mixer.h.
Added a build_config.c in order to decouple pwm_common.h from config.h.
Finally, battery configuration values now live in a batteryConfig
structure which means that battery.c does not depend on config.h and all
of it's dependencies.
Fixed the use of plurals on defines that were not collection objects.
PIDITEMS and CHECKBOXITEMS are now PID_ITEM_COUNT and
CHECKBOX_ITEM_COUNT.
status in cli now prints cpu MHz, 72 when running off crystal, 64 when running off intrc.
corrected WHO_AM_I check for mpu6050 when it's used on alternate address (AD0 high).
corrected PWM driver to consider CPU clock for timer prescalers - now things properly work below 72MHz
added a neat hack for pitch angle calculation so that it's not affected when roll reaches 90deg
added proper math for vector rotation instead of small-angle approximation
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@225 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
removed camtrig stuff since it wasnt possible. somewhat replaced with aux forwarding (see below)
2.1 buzzer code changed, untested.
removed flying wing mixer. nobody used that.
added alt_hold_throttle_neutral, nav_slew_rate and looptime configuration to cli. default looptime set to 3000. changed default gyro_cmpf to 400 to sync with 2.1.
increased bmp085 oversampling
added gimbal_flags (bit 4 set) flag which, in PPM mode, forwards AUX1..4 to the lower 4 PWM outputs instead of using them as motors. set gimbal_flags=8 to test it out. output is fixed to 50Hz.
merged 2.1 gps changes (not many)
casting in gyro smoothing (nobody uses that anyway)
calibrate accel in gimbal mode, set smallangle in gyro-only mode
vtail4 mixer fix
flight tested on quadx w/ppm.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@182 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
changed booleans to bitfield struct to match with 0622
no other functional changes, and not all enhancements (like boxlight) from 0622 are implemented yet
NOT flight tested, use at your own risk.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@172 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
new config ooptions for failsafe, so current settings are cleared
fixed mistake where yaw servo stuff for tri was still hardcoded even though it had configurable values in cli
reduced level default D to 20 from 100 (dunno what effect this has, shrug)
untested, enable feature FAILSAFE at your own risk.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@155 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
fixed spacing in ledring.c
defaulted acc_lpf to 100
correction in vtail4 mix (from multiwii_dev)
trashed more unused LOG_VALUES crap
no binary build since this is untested / non-flight-tested.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@152 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
