* PID controller unittest
* Clean code for yaw spin recovery
* Yaw spin recovery optimizations
* Flash size optimizations, use 50% throttle when airmode is off, and override pidsum_limit_yaw
Also rebasing from betaflight/master
Previously the gyro_overflow_detect and fallback slew filter were based on target definitions to determine whether the flight controller had an affected gyro to enable protection. The problem is that some targets are available with multiple gyro options and if one of those options was an affected gyro then all flight controllers for that target would have the oveflow code enabled even if they had a non-affected gyro. Also targets that include multiple gyros on-board and are selectable at runtime were not differentiated and forced overflow handling on even if the selected gyro was not affected.
For non-affected gyros the overflow handling code is not required and reduces recovery performance so it's not desirable to have it enabled when unnecessary.
In the case of dual-gyro targets if gyro_to_use = BOTH then if either is an affected gyro then overflow handling will be enabled.
* Revert "Revert "Rewritten F7 dshot to LL (draft)" (#5430)"
This reverts commit aa42a69d2f.
* Reworked F7 linker scripts to maximize performance of both F74x and F72x
* Some comments and changes from original F7 HAL DSHOT
* Prohibit inlining of some functions to place them in ITCM-RAM
* Fixed usartTargetConfigure implicit declaration
* Moved back to SRAM1 as main RAM
* Added SRAM2 attribute
* Fixed LL DSHOT FOR SPRF7DUAL and probably other adv TIM users
* Fixed SPRF7DUAL rev. A motor order
* Enabled CCM for data on F40x
* Fixed F7 startup assembly symbols
* Fixed KISSFCV2F7 linker script
* Added a quick way of building F7 targets only
* Got rid of the useless F7 target script
* Added NOINLINE and got rid of useless __APPLE__ define
* Added some important functions to ITCM
* Added NOINLINE macro for tests
* Copy to ITCM before passing execution into it
* Minimized cache footprint of motor output code
* Evicted low-impact functions from ITCM
* Switched MATEKF722 and SPRACINGF7DUAL to burst DSHOT
* Switched CLRACINGF7 to burst DSHOT
* Moved UART RX&TX buffers to DTCM-RAM to avoid cache incoherency
* Marked taskMainPidLoop for ITCM-RAM, disallowed inlining per-function
* Revert "Added a quick way of building F7 targets only"
This reverts commit 2294518998.
Previously only vbat_scale was exposed. Adds vbat_divider and vbat_multiplier parameters.
Note that all of these parameters only apply to the first voltage sensor (VOLTAGE_SENSOR_ADC_VBAT). There is the capability to have multiple sensors and those will not have their parameters exposed. Currently there are no target definitions that use multiple sensors.
The old gyro_lpf setting was based on the DLPF_CFG values for the MPU6050 gyro and the enumeration was inaccurate and misleading. For example, the default "OFF" setting did not disable the DLPF, but actually set it to around 250hz. The actual cutoff frequency for each setting varies by gyro hardware so the literal frequencies in the enumeration were also incorrect.
Removed gyro_lpf and replaced it with gyro_hardware_lpf (8KHz) and gyro_32khz_hardware_lpf (32KHz). The parameters were renamed to indicate that they are hardware filtering options to differentiate from the many software lowpass filtering options.
gyro_hardware_lpf - This parameter sets the filtering and sample rate options for 8KHz gyros (or 32KHz capable gyros running in 8KHz mode).
- NORMAL - default setting that is equivalent to the previous "OFF" setting. Configures 8KHz sampling with ~250Hz filter cutoff.
- EXPERIMENTAL - 8KHz sampling with a higher frequency filter cutoff (around 3000hz). Considerably more noisy and requires additional software filtering. Note that for the MPU6000 Invensense doesn't officially document the filter cutoff frequency for this selection and simply lists it as "reserved". In testing it's clear that a higher frequency filter cutoff is being selected due to the increased noise, but the actual cutoff frequency is unknown.
- 1KHZ_SAMPLING - 1KHz sample rate with and approximate 188Hz filter cutoff.
Note that the following additional 1KHz sample rate options with lower filter cutoffs have been eliminated - "98HZ", "42HZ", "20HZ", "10HZ", "5HZ". It seems unlikely that these are still needed are probably no longer viable and flight performance would be very poor.
gyro_32khz_hardware_lpf - This parameter sets the filtering options while running in 32KHz mode on capable gyros. It also exposes a new high frequency filter cutoff mode.
- NORMAL - The default and matches the current settings used for 32KHz mode. Provides a filter cutoff around 3000Hz.
- EXPERIMENTAL - Selects a filter cutoff around 8000Hz. This is a very noisy setting and will require substantial software filtering.
The default values for both 8KHz and 32KHz sample rates were chosen to match the previous defaults and users should not experience any performance differences.
Normalized the gyro initialization. Previously there was little consistency on how the initialization was performed and the settings interpreted. For example, MPU9250 used a completely different logic tree when configuring the registers.
Disconnected the literal parameter value from the gyro initialization. The gyro_lpf parameter contained a number from 0-7 that was literally applied to the configuration register during the gyro initialization. This caused some older gyro initializations to be incorrect as they used a different register layout (MPU3050 and L3G4200D). By transitioning to a logical selection the actual value applied to the hardware register is abstracted. This will better future-proof the design as new gyros may have a different register structure that may be incompatible with the old method.
Added a gyroregisters command to the CLI that is used to read the current register settings from the gyro and dump them to the CLI. This is used to verify the configuration in comparison to the datasheets for the various gyros. Testing empirically by looking at the relative noise from the gyros can give a rough estimate whether the different options are selecting correctly, but it's not very precise. The code for the gyroregisters CLI command is wrapped inside #ifdef USE_GYRO_REGISTER_DUMP blocks to allow easy disabling. It's currently enabled for all targets but we may decide to disable before release or only limit to targets with more available space (>=F4).
* Dual-stage Gyro Filtering: PT1, FKF, and Biquad RC+FIR2
* Builds on the previous work of apocolipse.
* Fixes 'stage2'/'stage1' mis-naming to reflect where it is applied in the loop.
That is, the older Biquad, PT1, Denoise (FIR) filters are 'stage2' - applied
after dynamic and static notches (if enabled), and the controversial PT1,
'fast Kalman' filter, and Biquad RC+FIR2 filters, are 'stage1'. e.g. before
dynamic notch.
* FKF bruteforce Kalman gain removed. Calculate from half of PT1 RC constant,
automatically taking loop-time into account.
* New union type definition for stage1 filtering.
* New gyro sensor members for stage1 filter application function and states for
all three supported filter types
* New enum types for stage1 v. stage2. dterm lowpass type references 'stage2'.
* updates to CMS/MSP/FC to allow compilation (untested, probably breaks
MSP, Lua, and ~comms with BFC~).
* Refactors FKF initialization, update and associated structures to be faster by
not continuously calculating 'k'. Filter gain is calculated once during
initialization from RC constant as per PT1 and Biquad RC+FIR2. It was
discovered this converges to static value within 100 samples at 32kHz, so can
be removed. Remove related interface (CLI) settings.
* update dterm_lowpass_type to use new 'TABLE_LOWPASS2_TYPE' (biquad/pt1/FIR)
* Stage 1 defaults to PT1, 763Hz (equivalent to Q400 / R88 from quasi-kalman
filter) - suitable for 32kHz sampling modes. Can be switched to Biquad
RC+FIR2, and FKF.
* Update `#if defined(USE_GYRO_SLEW_LIMITER) to `#ifdef`.
* Includes optional Lagged Moving Average 'smoothing' pipeline step, applied (in
code) after the output of stage1.
* (diehertz): Removed redundant pointers from gyro filtering
* blackbox: fix indentation
* cms IMU menu: fix indentation
* filters: remove USE_GYRO_FIR_FILTER_DENOISE in filter type enum
* gyro sensors: go back to `if defined()` form. for slew limiter
* gyro sensors: increment parameter group version
* due to non-appending changes, the version must be bumped.
* * FAST_RAM-ing variables used to compute FFT
* Eradicated global static variables in favour of define
* FFT_WINDOW_SIZE / 2 replaced with FFT_BIN_COUNT
* Limit call count of filters update to necessary minimum on 32k and 16k gyro sampling rate
* Dynamic filter recalculation freq. is at least FFT_SAMPLING_RATE + update time
* Moved global variables used in local scope only to local scope
* * Based on diehertzs review I removed all 0 initializations of global variables
* * Fixed calculation of update frequency for center frequency filter, thx rav-rav for pointing the problem
* * Silenced the warning signed vs unsigned comparison
* * Replaced magick values 3*4 and 12 with preprocessor macro as requested by DieHertz
* * Replaced hardcoded axis count with proper preprocessor macro
* CF/BF - Set STM32F7 SPI FAST clock to 13.5Mhz - Gyros not stable at
27mhz.
* CF/BF - Initial SPRacingF7DUAL commit.
Support two simultaneous gyro support (code by Dominic Clifton and Martin Budden)
There are new debug modes so you can see the difference between each gyro.
Notes:
* spi bus instance caching broke spi mpu detection because the detection
tries I2C first which overwrites the selected bus instance when using
dual gyro.
* ALL other dual-gyro boards have one sensor per bus. SPRacingF7DUAL is has two per bus and thus commit has a lot of changes to fix SPI/BUS/GYRO initialisation issues.
* CF/BF - Add SPRacingF4EVODG target.
This target adds a second gyro to the board using the SPI pads on the back of the board.
* CF/BF - Temporarily disable Gyro EXTI pin to allow NEO target to build.
* optimize math
Results in considerable flash saving
* log_approx, exp_approx, pow_approx
Taken from https://github.com/jhjourdan/SIMD-math-prims/blob/master/simd_math_prims.h
* Fix pow in rangefinder
* Use approximate function in baro calculation
Maximum error is < 20cm
* fixup! Fix pow in rangefinder
Noise and momentary spikes in gyro data (particularly in 32K mode) were causing false triggering of the gyro overflow detection. Changing to using filtered instead of raw gyro data eliminates the false triggering.
Also adjusted the trigger and reset rates slightly (approx. 1950dps and 1850dps respectively).
Fixed bug for gyros that may not be +-2000dps full scale. The trigger threshold will be 97.5% full-scale and reset at 92.5% (corresponds to 1950 and 1850 for 2000dps gyros).
Changed the triggering phase so that in addition to the pidSum needing to exceed runaway_takeoff_threshold, the gyro rate on any axis must exceed a threshold value to indicate the quad is actually moving. The threshold for the yaw axis is much higher since the torque of the motors can still yaw the craft without props.
Noise and momentary spikes in gyro data (particularly in 32K mode) were causing false triggering of the gyro overflow detection.
Also adjusted the trigger and reset rates slightly (approx. 1950dps and 1850dps respectively).
Optimized the gyro loop slightly by eliminating 3 floating point multiplies.
Fixed bug for gyros that may not be +-2000dps full scale.
* Generate 'k' per the code for the PT1
* Adjust function prototypes/functions to accept f_cut/dT where applicable
* Adjust gyro configuration, parameter group, interface settings to suit
Menu including:
- Voltage meter selection
- Current meter selection
- Max cell voltage (moved from MISC menu)
- Voltage scale adjust (moved from MISC menu)
- ADC current scale and offset adjust
- Virtual current scale and offset adjust
