On bad (out-of-range) pulses; ROLL, PITCH, YAW will go to `mid_rc` and
THROTTLE will go to `rx_min_usec` (to `mid_rc` for 3D mode). So these
channels will no longer be set by the user directly.
Fallback values for the aux switches (0 .. max) can be set with this
version. Since these switches may trigger all kind of things, the user
needs control over them in case of a RX failsafe event.
A single flight control channel failure (first 4) when using parallel
PWM is interpreted as a failure for all flight control channels (first
4), since the craft may be uncontrollable when one channel is down. (+4
squashed commit)
Squashed commit:
[dbfea9e] Apply fallback values also when serial_rx init failed and/or
RX
disconnected and/or no signal received.
[b5a2ecd] Added get/set MSP commands for RXFAIL config
Bumped API minor version up.
[c0e31ce] minor change for coding standard
[322705f] Added programmable RX channel defaults on rx lost Update #2
efficiently). Update MSP_SERVO_CONFIGURATIONS,
MSP_SET_SERVO_CONFIGURATION value order. Add some error checking to
size of MSP_SET_SERVO_CONFIGURATION.
* optimize for code size.
* consolidate error message handling.
* replace similar error messages with identical ones.
* shorten all strings where possible.
* made less verbose.
This was required for the CC3D OPBL build.
Main rule logic and MSP commands ported from baseflight.
Gimbal mixer updated to use rules. This allows us to remove more
conditional logic. Operation of gimbal servos is now different.
1) the 2 extra servos were not used for anything, yet.
2) the MSP packet to set ALL the servo configurations in one go is
larger than the MSP input buffer size.
Likely the MSP_SET_SERVO_CONF should be updated with command that takes
an index of a servo to configure, as per mode ranges/colors/leds/etc.
Fixes#1002
Remove duplicate consts.
Pull in the include files where functions and variables are declared.
Mark file local but duplicated variables as static.
Mark some variable declarations as extern.
Remove duplicated variable definition.
Signed-off-by: Michael Hope <mlhx@google.com>
...and apply them after a soft reset (which also required an additional
write to flash), it is now such that features and settings are modified
and stored in flash as before.
After initialisation completes, the active features are latched and are
not to be modified until the next startup. This guarantees that all
saved modifications are persistent even when power is switched of
(without a reset in between).
When a soft reset is required, the active features and the currently
configured features are used to detect if the oneshot feature has
changed state, in which case motor PWM outputs are stopped and soft
reset is done after a 1.5 second delay.
During normal operation the active features will not change and all
changes to features ordered via MSP commands or the CLI are applied to
the configuration that gets saved to flash.
The required effect of modifying features without changing the actions
in the running mainloop is achieved. The user needs to be aware that
changes to features are not applied immidiatly.
* fixes issue where indicators would flash when SBus RX entered failsafe
mode.
* fixes bug where turning off a TX for an SBus RX would instantly disarm
when using a switch to arm when the channel went outside the arming
range.
* introduces failsafe phases to make the system more understandable.
* allows the system to ask if rxSignalIsBeing received for all RX
systems: PPM/PWM/SerialRX/MSP. Also works when a serial data signal is
still being received but the data stream indicates a failsafe condition
- e.g. SBus failsafe flags.
* failsafe settings are no-longer per-profile.
Untested: Sumd/Sumh/XBus/MSP (!)
Tested: SBus X8R, Lemon RX Sat, X8R in PWM, Spektrum PPM.
Previously it was possible to set roll/pitch rate > 1.0 using MSP, but
not using the CLI. Roll/pitch rate > 1.0 is meaningless.
TPA is also limited to 1.0.
Enhanced MSP_RC_TUNING and MSP_SET_RC_TUNING. Configurator's PID Tuning tab can be enabled to update TPA Breakpoint.
PID Tuning tab must be enhanced for this feature. Agnostic if older versions of Configurator are used.
