The primary reason is to support the D4R-II with it's much faster PWM
frequency. The PWM RSSI code could not keep up, and since there are no
timers free for using capture compare of PWM signals in hardware one
solution is to use the ADC at a slow sample rate.
RC2 is used as before and it expects a signal between 0 and 3.3v. An
inline smoothing capacitor may help.
This commit also removes the cli command adc_power_channel since the
reading was never actually exposed anywhere.
full gyro scale is used now
and a new pid with float calculations was added based on PIDrewrite
eeprom size was also increased from 1kB to 2kB
Conflicts:
src/config.c
src/drivers/accgyro_l3g4200d.c
src/drivers/accgyro_mpu3050.c
src/drivers/accgyro_mpu6050.c
src/flight_imu.c
src/mw.c
src/mw.h
src/serial_cli.c
src/serial_msp.c
src/utils.c
src/utils.h
Also support FrSky 1khz RSSI. See documentation also added in this
commit.
This commit also cleans up the PWM mapping code. 'mask' didn't need to
be a mask and it wasn't possible to add another 'type' since there were
only 4 possible values when it was a mask and they were already defined.
Combined with switching to using 16 bits instead of 8 for the mapping
configurations, it's now possible to have 256 types instead of 4 at the
expense of a few bytes of flash.
Moved the RSSI calculation into rx_common.c, previously it was in the
main loop.
The index is not really a user concern and leads to confusion. gps
baudrate is not set like any other baud date and the determination of an
appropriate index is hidden from the user.
If the user specifies a baudrate that is not supported the default index
is used which is current the index for 115200.
This also allows GPS to work on softserial ports at up to 19200.
systems and Parallel PWM/PPM systems.
Added setting for failsafe_max_usec. Renamed failsafe_detect_threshold
to failsafe_min_usec.
Failsafe now detects when a PPM/PWM RX isn't sending ANY data out on
CH1-4. See documentation notes regarding Graupner receivers in
Failsafe.md.
Documented failsafe system.
own dedicated serial port.
Added a feature to enable/disable RX_MSP.
Renamed feature SERIALRX to RX_SERIAL.
Renamed feature PARALLEL_PWM to RX_PARALLEL_PWM
Renamed PPM to RX_PPM.
Update serial configuration checking to better support Serial RX and
telemetry by verifiying serial port features and supported baud rates.
It's now possible to use a low-speed serial rx provider via softserial -
only problem is all the current serial rx providers are 100000/115200
baud. The code changes however open the door for using serial rx and
any capable serial port such as uart3-5 on the STM32F30x
It's also now possible to use GPS at low speeds on software serial
ports.
meant that 1kb of code could be overwritten when saving the config.
Fixed EEPROM write address for F30x so that code is also not overwritten
when saving the config.
match the comment from pullrequest about spacing
remains : some hand alignment for comment and wrong /** */ usage.
Conflicts:
src/board.h
src/buzzer.c
src/config.c
src/drivers/serial_common.h
src/drivers/system_common.c
src/drv_gpio.h
src/drv_pwm.c
src/drv_timer.c
src/drv_uart.c
src/flight_imu.c
src/mw.c
src/serial_cli.c
This enables a new feature setting for PARALLEL_PWM which is enabled by
default.
This starts to move much of the feature checking/excluding code that is
littered through into a single place - validateAndFixConfig(). Since
the config is known to be valid after the method is called other code
can just get on with it's job instead of checking for confliciting
features/settings.
Currently port usage is hard-coded to the default port layout, cli
commands are coming in a future commit.
This decouples all code from the global 'serialPorts' structure which
has been removed. Any code that needs to use a serial port can use
findOpenSerialPort() and openSerialPort() and maintain it's own
reference to the port.
Ports can switch between functions. e.g. by default
cli/msp/telemetry/gps
passthrough all use USART1. Each port maintains it's current function.
see begin/endSerialPortFunction.
There are only certain combinations of serial port functions that are
supported, these are listed in serialPortFunctionScenario_e.
This commit also adds a few 'static' keywords to variables that should
have been.
There a a few other minor fixes and tweaks to various bits of code that
this uncovered too.
TIM8 correctly. Software serial conficted with parallel PWM input. Fixed
crash due to incorrect timerConfig index calculation code.
The crash occurred when capture compare interrupt handlers attempted to
call an invalid callback.
Note: the crash does not affect existing baseflight code since the
formula is OK when using a 2 dimensional array with equal dimensions.
Formula details here:
https://docs.google.com/spreadsheets/d/1UuxnC0VKiprvt1wt3KXffefEWJUb_-ILFLQuP377Anw
This is a large commit, from the commit it is clear that the mixer has
many dependencies, this is expected since it is central to the
application.
To achieve the decoupling many master config and profile members had to
be moved into structures.
Relocated throttle/pitch curves into rc_curves.c/h since it has nothing
to with rx code, this fixed the dependencies inside the rx provider
files.
Rename yawdeadband to yaw_deadband to match other variables/cli
commands.
Fix a couple of usages of MAX_MOTORS where MAX_SUPPORTED_MOTORS should
be used instead.
In doing so accelerometer sensor and trim code had to be cleaned.
Added a new method to buzzer.c to avoid exposing toggleBeep.
Renamed current_profile to current_profile_index to avoid confusion.
Moved some GPS code from mw.c into gps_common.c.
Moved pid values into a pidProfile_t structure; this was done so that
gps_common.c does not have a dependency on config_profile.h.
pidProfile_t lives in flight_common.h now.
Moved gps profile settings from profile_t into gpsProfile_t for the same
reason.
Removed gps_common.c's dependency on masterConfig_t by passing needed
variables into gpsInit().
separate concerns and help reduce and clarify dependencies.
cfg and mcfg are too similarly named and are not obvious. Renamed cfg
to currentProfile and mcfg to masterConfig. This will increase source
code line length somewhat but that's ok; lines of code doing too much
are now easier to spot.
each. relocated acc_t/gyro_t from sensors_common.h into
drivers/accgyro_common.h since they define an interface and the
dependency was pointing the wrong way from the drivers.
baro_t/acc_t/gyro_t dependences are all now pointing the right way.
the code is doing. There are now no EEPROM read/write/reset/verify
methods that take any arguments which removes magic boolean variables
from method signatures.
This also removes duplicate code in the cliDefaults and cliSave commands
which results in smaller code also also due to the deduplication of a
reboot message.
only what it's name implies and it's method takes no arguments. This
avoids the 0/1 magic numbers which was a flag to decide whether the user
should be notified after the EEPROM has been read (!).
Introduced a method called readEEPROMAndNotify() which is used in all
cases where writeEEPROM(1) was previously called.
Additionally this avoid re-reading the profile when the reboot command
is issued which speeds up reboots.
Finally this avoid needless comments because the code tells you now what
it is going to do.
serial_common.c/h. decouple runtime_config from serial ports. decouple
buzzer from serial ports. decouple opening of the main serial port from
the msp code. decouple serial rx providers from runtime_config. rename
core_t to serialPorts_t since it only contained serial ports. It's now
clear which files use serial ports based on the header files they
include.
of determining a revision code. Previously there was mpu6050 specific
code in cli.c (the status command).
Finally this commit has removed all non-serial port configuration
settings from core_t so that a future commit can refactor core_t to
reduce dependencies on serial port code.
In doing this I also noted from other source code that the MPU6050
accelerometer trim for some revisions appeared to be incorrectly set to
255 * 8 instead of 256 * 8.
capability flag which is returned by MSP IDENT (CAP_CHANNEL_FORWARDING).
Adds two new MSP commands that are specifically for configuring channel
forwarding (MSP_CHANNEL_FORWARDING/MSP_SET_CHANNEL_FORWARDING). Servo
'middle' and 'forward from channel' are now stored independently, as
they probably should always have been.
code into rx_common.c. Moved some GPS code into gps_common.c. Isolated
some GPS functions into gps_common.c that were called from mw.c/loop().
moved gimbal defines into gimbal.h. Moved sound & light code into
statusindicator.c
