PWM6+7/TIM3_CH3+4/PB0+PB1
Update software serial to monitor serial pins for signal changes instead
of periodically sampling pin signals.
When reading the data the timer used is syncronized to the falling edge
of the start bit which allows for better syncronisation at higher
speeds. The code has been tested OK from 1200 baud to 19200. 38400
baud was tested and partially usable but has been disabled because there
are too many transmit and receive errors, especially when transmitting
and receiving at the same time.
Due to the way a single timer is used for transmitting and receiving, if
data comes in while transmitting the system may incorrectly transmit a
short or long bit. However at 19200 and below this didn't cause a
problem in the limited testing I performed.
althold should work better now, the PID settings are preliminary. There
is definetly room for improvement.
For aquiring your own PID settings set ALT_P = 0 and tune the VEL pid
until the copter only drifts a little from its position when you
activate althold. Then set ALT_P to a value where it holds the position
stable
If telemetry_switch=1 it change baudrate and protocol using aux channel, either it switch when armed/disarmed.
This allows to keep MSP serial while armed for BT dongle if needed.
see comments in code for things to fix. added new variable to cli, fixedwing_althold_dir (though its value isn't really clear, I think it should always be positive since servo direction mix is done later).
* Proper initialization sequence framework for various supported GPS types. NMEA will now auto-detect its baud rate based on received frames.
* As a result of the above, gps_baudrate has been changed to enum, to only allow fixed rates. (GPS baudrate, -1: autodetect (NMEA only), 0: 115200, 1: 57600, 2: 38400, 3: 19200, 4: 9600)
* UBX binary initialization at any specified baudrate with auto-reconnect on signal loss.
* GPS thread to handle initialization, signal loss and configuration. No longer does GPS need to be powered before FC, and on GPS reconnect, it will be re-initialized if needed.
MTK NMEA/binary initialization is omitted for now, as I can't find my MTK GPS
GPS deltaTime can be calculated to display update rate.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@438 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
FEATURE_SPEKTRUM has been removed and replaced with FEATURE_SERIALRX.
cli option serialrx_type now configures what type of receiver it is
0 = spektrum1024, 1 = spektrum2048, 2 = sbus
sbus will need hardware inverter to use.
also cleaned up receiver drivers to assign readrawRC callback instead of assigning in code in main()
none of this has been tested.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@418 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
tri_unarmed_servo to 1 (default) always updates tri servo whether armed or not.
tri_unarmed_servo to 0 will only send servo signal to tail servo when armed.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@392 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
+ this is a per-profile setting, and PIDs CHANGE from default multiwii ones. check the above forum post for PID examples. set pid_controller = 0 for default multiwii, or 1 for new one.
= went back to clearing clibuffer after each command
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@341 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added and began work on integrating failsafe_detect_threshold
got rid of acc_lpf_for_velocity since that seemed no longer used.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@317 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
defaulted to looptime of 3500 (yea, yea)
rewrote baro stuff to match mwc2.2 - both supported sensors now return temperature and pressure, which is used in altitude calculation code
rewrote hmc5883 driver to include calibration inside the driver file instead of calling parts of calibration from userspace. it will now blink LED1 while calibrating
some parts remaining to do.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@298 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
mw2.2-merged stuff:
* implemented profiles 0-2 (called 'setting' in mwiigui)
* merged in MSP changes including profile switch
* cleaned up rc / aux switch stuff in mw.c based on 2.2 rewrite
* main loop switch for baro/sonar shit adjusted
todo: basically the rest of 2.2 changes (i think some minor imu/gps/baro updates)
baseflight-specific stuff:
* made boxitems transmission dynamic, based on enabled features. no more GPS / camstab trash if it's not enabled
* cleaned up gyro drivers to return scale factor to imu code
* set gyro_lpf now controls every supported gyro - not all take same values, see driver files for allowed ranges, in case of invalid lpf, defaults to something reasonable (around 30-40hz)
maybe couple other things I forgot. this is all 100% experimental, untested, and not even flown. thats why there's no hex.
merge is still ongoing.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@294 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
fixed pwm init for airplane mode mistakenly deleting motors from the mix. flyingwing should really work now.
removed led debug from althold
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@223 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
refactored all of mixer.c to use tables instead of hardcoded mix.
custom mixer is stored in flash, but currently has no UI to configure it.
do not choose mixer CUSTOM in console.
hover-tested QUADX, if upgrading anything else, please carefully check motor response first, preferably without props on heavy models.
tec
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@206 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
use set gps_type=X in cli to configure, where X=0 if NMEA (no special config), X=1 if UBX (enters ubx binary mode), X=2 if MTK (sets up MTK for 5Hz operation).
changed default GPS rate to 115200 baud
added baudrate reset stuff to UART driver for GPS autoconfigure
NONE of this is tested (except UBX working on my window)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@204 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added interrupt pins from mag/mma/mpu for rev4 hardware. nothing done with them yet - candidates for EXTI use
added tx buffer to UART2 (gps) in preparation for auto-config
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@203 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
