Mirror/inav
1
0
Fork 0
mirror of https://github.com/iNavFlight/inav.git synced 2025-07-23 16:25:26 +03:00
Code Issues Wiki Activity

Closes #584

Browse source
This commit is contained in:
Paweł Spychalski 2016-09-11 15:16:51 +02:00 • committed by GitHub
parent 6cc415a312
commit b876fd66e6
1 changed files with 2 additions and 2 deletions
Download patch file Download diff file Expand all files Collapse all files

4
docs/Cli.md
View file

@ -107,7 +107,7 @@ Re-apply any new defaults as desired.
| `emf_avoidance` | Default value is 0 for 72MHz processor speed. Setting this to 1 increases the processor speed, to move the 6th harmonic away from 432MHz. | OFF | ON | OFF | Master | UINT8 |
| `i2c_overclock` | Default value is 0 for disabled. Enabling this feature speeds up IMU speed significantly and faster looptimes are possible. | OFF | ON | OFF | Master | UINT8 |
| `gyro_sync` | Default value is Off. This option enables gyro_sync feature. In this case the loop will be synced to gyro refresh rate. Loop will always wait for the newest gyro measurement. Use gyro_lpf and gyro_sync_denom determine the gyro refresh rate. Note that different targets have different limits. Setting too high refresh rate can mean that FC cannot keep up with the gyro and higher gyro_sync_denom is needed, | OFF | ON | OFF | Master | UINT8 |
| `gyro_sync_denom` | This option determines the sampling ratio. Denominator of 1 means full gyro sampling rate. Denominator 2 would mean 1/2 samples will be collected. Denominator and gyro_lpf will together determine the control loop speed. | 0 | 1 | 1 | Master | UINT8 |
| `gyro_sync_denom` | This option determines the sampling ratio. Denominator of 1 means full gyro sampling rate. Denominator 2 would mean 1/2 samples will be collected. Denominator and gyro_lpf will together determine the control loop speed. | 1 | 32 | 1 | Master | UINT8 |
| `mid_rc` | This is an important number to set in order to avoid trimming receiver/transmitter. Most standard receivers will have this at 1500, however Futaba transmitters will need this set to 1520. A way to find out if this needs to be changed, is to clear all trim/subtrim on transmitter, and connect to GUI. Note the value most channels idle at - this should be the number to choose. Once midrc is set, use subtrim on transmitter to make sure all channels (except throttle of course) are centered at midrc value. | 1200 | 1700 | 1500 | Master | UINT16 |
| `min_check` | These are min/max values (in us) which, when a channel is smaller (min) or larger (max) than the value will activate various RC commands, such as arming, or stick configuration. Normally, every RC channel should be set so that min = 1000us, max = 2000us. On most transmitters this usually means 125% endpoints. Default check values are 100us above/below this value. | 0 | 2000 | 1100 | Master | UINT16 |
| `max_check` | These are min/max values (in us) which, when a channel is smaller (min) or larger (max) than the value will activate various RC commands, such as arming, or stick configuration. Normally, every RC channel should be set so that min = 1000us, max = 2000us. On most transmitters this usually means 125% endpoints. Default check values are 100us above/below this value. | 0 | 2000 | 1900 | Master | UINT16 |
@ -256,7 +256,7 @@ Re-apply any new defaults as desired.
| `flaperon_throw_offset` | Defines throw range in us for both ailerons that will be applied (before scaling) when FLAPERON mode is activated. | 100 | 400 | 250 | Profile | UINT16 |
| `flaperon_throw_inverted` | Inverts throw offset on both ailerons. Can be used to create SPOILERON or just to change throw direction | OFF | ON | OFF | Profile | UINT8 |
## New iNav spesific
## New iNav specific
| `Variable` | Description/Units | Min | Max | Default | Type | Datatype |
|-----------------------------------------------|--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|--------|--------|------------------|--------------|----------|
| `acczero_x` | Calculated value after '6 position avanced calibration'. See Wiki page. | 0 | 0 | 0 | Master | UNKNOWN |