documented L3G4200D driver why 0x28 read was suddenly turning into 0xA8
removed old wiimotion averaging cruft from computeIMU
NOT FLIGHT TESTED
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@403 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
tri_unarmed_servo to 1 (default) always updates tri servo whether armed or not.
tri_unarmed_servo to 0 will only send servo signal to tail servo when armed.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@392 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
+ this is a per-profile setting, and PIDs CHANGE from default multiwii ones. check the above forum post for PID examples. set pid_controller = 0 for default multiwii, or 1 for new one.
= went back to clearing clibuffer after each command
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@341 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added and began work on integrating failsafe_detect_threshold
got rid of acc_lpf_for_velocity since that seemed no longer used.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@317 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
defaulted to looptime of 3500 (yea, yea)
rewrote baro stuff to match mwc2.2 - both supported sensors now return temperature and pressure, which is used in altitude calculation code
rewrote hmc5883 driver to include calibration inside the driver file instead of calling parts of calibration from userspace. it will now blink LED1 while calibrating
some parts remaining to do.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@298 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
mw2.2-merged stuff:
* implemented profiles 0-2 (called 'setting' in mwiigui)
* merged in MSP changes including profile switch
* cleaned up rc / aux switch stuff in mw.c based on 2.2 rewrite
* main loop switch for baro/sonar shit adjusted
todo: basically the rest of 2.2 changes (i think some minor imu/gps/baro updates)
baseflight-specific stuff:
* made boxitems transmission dynamic, based on enabled features. no more GPS / camstab trash if it's not enabled
* cleaned up gyro drivers to return scale factor to imu code
* set gyro_lpf now controls every supported gyro - not all take same values, see driver files for allowed ranges, in case of invalid lpf, defaults to something reasonable (around 30-40hz)
maybe couple other things I forgot. this is all 100% experimental, untested, and not even flown. thats why there's no hex.
merge is still ongoing.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@294 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
fixed pwm init for airplane mode mistakenly deleting motors from the mix. flyingwing should really work now.
removed led debug from althold
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@223 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added VAR_FLOAT to cli - now allows setting/printing float vars
fixed newlines in pwm driver
exported new althold tunables to cli (some are floats) - still not enabled by default until I know it works
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@219 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
synced angle/horizon mode stuff from mwc. no idea what it does.
perhaps the most important part of this update:
-errorAngle = constrain(2 * rcCommand[axis] - GPS_angle[axis], -500, +500) - angle[axis] + cfg.angleTrim[axis];
+errorAngle = constrain(2 * rcCommand[axis] + GPS_angle[axis], -500, +500) - angle[axis] + cfg.angleTrim[axis];
(which means GPS might actually work).
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@209 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
refactored all of mixer.c to use tables instead of hardcoded mix.
custom mixer is stored in flash, but currently has no UI to configure it.
do not choose mixer CUSTOM in console.
hover-tested QUADX, if upgrading anything else, please carefully check motor response first, preferably without props on heavy models.
tec
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@206 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added interrupt pins from mag/mma/mpu for rev4 hardware. nothing done with them yet - candidates for EXTI use
added tx buffer to UART2 (gps) in preparation for auto-config
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@203 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added ms5611 driver
refactored pressure sensor subsystem to allow multiple sensors
couple changes in PWM driver to make motor/servo arrangement for airplane mode more intuitive
moved MAX_MOTORS/MAX_SERVOS etc into drv_pwm.h
staring to merge back in airplane/flyingwing mixes
fix for tri servo display - mwc moved it to servo[5] again, gui was broken, function not.
will probably implement custom mixer soon (motors only, no servos)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@198 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
removed camtrig stuff since it wasnt possible. somewhat replaced with aux forwarding (see below)
2.1 buzzer code changed, untested.
removed flying wing mixer. nobody used that.
added alt_hold_throttle_neutral, nav_slew_rate and looptime configuration to cli. default looptime set to 3000. changed default gyro_cmpf to 400 to sync with 2.1.
increased bmp085 oversampling
added gimbal_flags (bit 4 set) flag which, in PPM mode, forwards AUX1..4 to the lower 4 PWM outputs instead of using them as motors. set gimbal_flags=8 to test it out. output is fixed to 50Hz.
merged 2.1 gps changes (not many)
casting in gyro smoothing (nobody uses that anyway)
calibrate accel in gimbal mode, set smallangle in gyro-only mode
vtail4 mixer fix
flight tested on quadx w/ppm.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@182 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added a modifier for set (type "set *") to see min/max values for each parameter. this is for gui stuff
bumped config VERSION
fixed 0xffff - now stuff in drv_pwm, after it was mentioned to me for the 3rd time :p
replaced some uint8_t -> uint32_t for loop counters - saving 4 to 8 bytes of flash each time. thanks goes to thee 35+ years of C experience kicad guy.
turned bitfiends into a regular struct - instant 100byte flash size reduction
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@174 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
feature TELEMETRY to enable it. when armed, telemetry is sent out the TX pin. It must be connected to 'Rx' pin of FrSky telemetry receiver via a level shifter. When disarmed, port goes back to 115200 bps for GUI.
fixed a typo in imu.c introduced by GYRO_INTERLEAVE junk.
todo: just switch serial speed instead of reinitializing everything.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@173 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
changed booleans to bitfield struct to match with 0622
no other functional changes, and not all enhancements (like boxlight) from 0622 are implemented yet
NOT flight tested, use at your own risk.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@172 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
applied mwc-dev GPS code with bits of tarducopter code by sbaron. Thanks again. Moved some of the GPS config stuff into cli - gps_lpf, min/max nav speed, nav_controls_heading. Remember I don't test any GPS functionality at all, so if this makes your quad fly towards North Korea at over 9000cm/sec, this is NOT my problem.
spacing fixes in a couple files.
trashed old serial code that was under #if 0
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@161 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added arm/disarm on left/righ roll while throttle down to configuration options and disabled it by default. "set retarded_arm" in CLI
put gyro_cmpf_factor into settings. default is 310, can be increased to decrease acc influence. debug use only.
dropped acc_lpf_factor back to 4. those who want it at 100, make it so.
cleaned up MPU6050 driver with humanreadable register names
got rid of MMGYRO crap - no use
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@159 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added mag_declination set option to cli - oops
status in cli now prints which ACC hardware is used. work in proress to show difference between hardware with MPU6050 and MPU3050
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@157 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
new config ooptions for failsafe, so current settings are cleared
fixed mistake where yaw servo stuff for tri was still hardcoded even though it had configurable values in cli
reduced level default D to 20 from 100 (dunno what effect this has, shrug)
untested, enable feature FAILSAFE at your own risk.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@155 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
new hex file only works with Java GUI 20120504-dev :( WinGUI is still not updated. Use latest release version on downloads page if want to use WinGUI.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@153 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
fixed spacing in ledring.c
defaulted acc_lpf to 100
correction in vtail4 mix (from multiwii_dev)
trashed more unused LOG_VALUES crap
no binary build since this is untested / non-flight-tested.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@152 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added fifo mode to adxl345 driver, currently disabled. work in progress.
fixed output for PWM 5-8 when used with PPM + camstab + abovequad configs.
fixed baro, now alt-hold actually works. silly copypaste typo.
trashed all remaining parts of power meter and lcd configuration stuff. useless.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@145 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added float-based acc lpf, acc_lpf_factor values now changed, its 1/factor now, values 60+ and larger filter heavier.
playing with release MPU6050 hardware, looks like acc1G is fucked, as predicted
bug in serial output (forgot to output armed bit to GUI, estalt is /10)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@144 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
whitespace fixes in mw.h and trashed the old XA-XB based mixer setting leftovers.
settings are cleared again due to updated config struct.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@138 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
removed feature digital_servo since its now set by cli instead.
added proper tx end check into uart, to remove delay inside printing out set values and tx buffer overrun during help()
instead of passing a bunch of params to pwm driver, made a config struct
fixed a bug in gps baudrate
fixed typo in stmloader.c
whitespace / indentation cleanups in various drivers
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@137 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
