- Added failsafe flightmode and rc control box.
To make failsafe procedure a separate flight mode and make it possible
to trigger failsafe with an AUX switch.
- Failsafe mode is activated when failsafe is active.
RC link lost is simulated with the failsafe AUX switch.
When NOT armed: failsafe switch to failsafe mode is shown in GUI (mode
tab).
- Activate failsafe mode with AUX switch.
- Prevent arming when failsafe via AUX switch is active (safety issue).
- Make failsafe disarm if motors armed and throttle was LOW (2D & 3D)
for `failsafe_throttle_low_delay` time (__JustDisarmEvent__).
Applied code changes to effectively add pull request: Make failsafe
disarm if motors armed and throttle low #717.
- Use failsafeIsMonitoring() to actually start monitoring.
- Added `failsafe_kill_switch` to code.
When set to 1 (0 is default), the failsafe switch will instantly disarm
(__KillswitchEvent__) instead of executing the landings procedure.
Arming is NOT locked after
this, so the craft could be re-armed if needed.
This is intended for racing quads where damage and danger must be
minimized in case of a pilot error.
- Added `failsafe_throttle_low_delay`, adapted documentation.
Used to adjust the time throttle level must have been LOW
to _only disarm_ instead of _full failsafe procedure_
(__JustDisarmEvent__).
- Updated the failsafe documentation.
- Re-enable arming at end of failsafe procedure.
At the end of a handled failsafe event, that means: auto-landing,
__JustDisarmEvent__ or __KillswitchEvent__, the RX link is monitored for
valid data.
Monitoring is a part of the failsafe handling, which means the craft is
still in failsafe mode while this is done.
Arming is re-enabled (allowed) when there is a valid RX link for more
then XX seconds, where XX depends on the handled event like this:
1. XX = 30 seconds after auto landing.
2. XX = 3 seconds after __JustDisarmEvent__.
3. XX = 0 seconds after __KillswitchEvent__.
NOTE: When armed via an AUX switch, you will have to switch to the
disarmed position at the very end to be able to re-arm.
The failsafe mode will not end until you do.
- __KillswitchEvent__ has now priority over __JustDisarmEvent__
- Apply rxfail values instantly when failsafe switch is ON
- Added missing cases to display.c
Show M when failsafe is monitoring for RX recovery (AND disarming when
armed with a switch).
===
Reworked the code from counter-based to time-based.
- AUX failsafe switch now has identical behavior to RX loss.
- Added RX failure and RX recovery timing.
- __KillswitchEvent__ skips RX failure detection delay (direct disarm).
===
[UNIT TESTS]
Adapted failsafe related unittests from counter-based to time-based
- Added failsafeOnValidDataFailed() to some tests
- Removed duplicate test setup from rc_controls_unittest.cc
- Removed magic numbers from rx_ranges_unittest.cc and rx_rx_unittest.cc
- Reworked all test-cases for flight_failsafe_unittest.cc
Remove duplicate consts.
Pull in the include files where functions and variables are declared.
Mark file local but duplicated variables as static.
Mark some variable declarations as extern.
Remove duplicated variable definition.
Signed-off-by: Michael Hope <mlhx@google.com>
* fixes issue where indicators would flash when SBus RX entered failsafe
mode.
* fixes bug where turning off a TX for an SBus RX would instantly disarm
when using a switch to arm when the channel went outside the arming
range.
* introduces failsafe phases to make the system more understandable.
* allows the system to ask if rxSignalIsBeing received for all RX
systems: PPM/PWM/SerialRX/MSP. Also works when a serial data signal is
still being received but the data stream indicates a failsafe condition
- e.g. SBus failsafe flags.
* failsafe settings are no-longer per-profile.
Untested: Sumd/Sumh/XBus/MSP (!)
Tested: SBus X8R, Lemon RX Sat, X8R in PWM, Spektrum PPM.
the value for small angle. The latter is to help get field reports to
help with a problem where sometimes the aircraft won't arm because the
FC thinks it's tilted over too much.
Note: not working on the sparky, MPU9150 needs passthough enabling but
when enabled the mag and gyro won't ack on the default addresses. Needs
further investigation.
size to work with Glonass MSG-SVINFO packets. Skip data from packets
that are too large to process without attempting to process a large
payout as packet data. Ignore GPS presence check when enabling
passthrough mode so that it is possible to configure a GPS unit via the
FC without the GPS unit actually having communicated to the FC first.
enabled/disabled via cli (disabled by default now). Fix missing rate
configuration for UBLOX SVINFO which would have resulted in missing
satallite counts.
the display when the page changes in the hopes the hardware responds.
This also allows the user to power off/on the display or connect it
while powered.
