Mirror/betaflight
1
0
Fork 0
mirror of https://github.com/betaflight/betaflight.git synced 2025-07-25 09:16:07 +03:00
Code Issues Wiki Activity
betaflight/src/mw.c
timecop@gmail.com 4ed57b2696 fix for airplane pwm mode - variable wasn't initialized, resulting in non-working motors on some compilers. 
synced angle/horizon mode stuff from mwc. no idea what it does.
perhaps the most important part of this update:
-errorAngle = constrain(2 * rcCommand[axis] - GPS_angle[axis], -500, +500) - angle[axis] + cfg.angleTrim[axis];
+errorAngle = constrain(2 * rcCommand[axis] + GPS_angle[axis], -500, +500) - angle[axis] + cfg.angleTrim[axis];
(which means GPS might actually work).

git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@209 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
2012-09-08 08:15:16 +00:00

649 lines
25 KiB
C
Executable file
Raw Blame History

#include "board.h"
#include "mw.h"
// July 2012 V2.1
flags_t f;
int16_t debug[4];
uint8_t toggleBeep = 0;
uint32_t currentTime = 0;
uint32_t previousTime = 0;
uint16_t cycleTime = 0; // this is the number in micro second to achieve a full loop, it can differ a little and is taken into account in the PID loop
int16_t headFreeModeHold;
int16_t annex650_overrun_count = 0;
uint8_t vbat; // battery voltage in 0.1V steps
int16_t telemTemperature1; // gyro sensor temperature
int16_t failsafeCnt = 0;
int16_t failsafeEvents = 0;
int16_t rcData[8] = { 1502, 1502, 1502, 1502, 1502, 1502, 1502, 1502 }; // interval [1000;2000]
int16_t rcCommand[4]; // interval [1000;2000] for THROTTLE and [-500;+500] for ROLL/PITCH/YAW
int16_t lookupPitchRollRC[6]; // lookup table for expo & RC rate PITCH+ROLL
int16_t lookupThrottleRC[11]; // lookup table for expo & mid THROTTLE
rcReadRawDataPtr rcReadRawFunc = NULL; // receive data from default (pwm/ppm) or additional (spek/sbus/?? receiver drivers)
uint8_t dynP8[3], dynI8[3], dynD8[3];
uint8_t rcOptions[CHECKBOXITEMS];
int16_t axisPID[3];
// **********************
// GPS
// **********************
int32_t GPS_coord[2];
int32_t GPS_home[2];
int32_t GPS_hold[2];
uint8_t GPS_numSat;
uint16_t GPS_distanceToHome; // distance to home point in meters
int16_t GPS_directionToHome; // direction to home or hol point in degrees
uint16_t GPS_altitude, GPS_speed; // altitude in 0.1m and speed in 0.1m/s
uint8_t GPS_update = 0; // it's a binary toogle to distinct a GPS position update
int16_t GPS_angle[2] = { 0, 0 }; // it's the angles that must be applied for GPS correction
uint16_t GPS_ground_course = 0; // degrees*10
uint8_t GPS_Present = 0; // Checksum from Gps serial
uint8_t GPS_Enable = 0;
int16_t nav[2];
int16_t nav_rated[2]; // Adding a rate controller to the navigation to make it smoother
int8_t nav_mode = NAV_MODE_NONE; // Navigation mode
//Automatic ACC Offset Calibration
// **********************
uint16_t InflightcalibratingA = 0;
int16_t AccInflightCalibrationArmed;
uint16_t AccInflightCalibrationMeasurementDone = 0;
uint16_t AccInflightCalibrationSavetoEEProm = 0;
uint16_t AccInflightCalibrationActive = 0;
// Battery monitoring stuff
uint8_t batteryCellCount = 3; // cell count
uint16_t batteryWarningVoltage; // annoying buzzer after this one, battery ready to be dead
void blinkLED(uint8_t num, uint8_t wait, uint8_t repeat)
{
uint8_t i, r;
for (r = 0; r < repeat; r++) {
for (i = 0; i < num; i++) {
LED0_TOGGLE; // switch LEDPIN state
BEEP_ON;
delay(wait);
BEEP_OFF;
}
delay(60);
}
}
#define BREAKPOINT 1500
// this code is executed at each loop and won't interfere with control loop if it lasts less than 650 microseconds
void annexCode(void)
{
static uint32_t calibratedAccTime;
uint16_t tmp, tmp2;
static uint8_t buzzerFreq; //delay between buzzer ring
static uint8_t vbatTimer = 0;
uint8_t axis, prop1, prop2;
static uint8_t ind = 0;
uint16_t vbatRaw = 0;
static uint16_t vbatRawArray[8];
uint8_t i;
// PITCH & ROLL only dynamic PID adjustemnt, depending on throttle value
if (rcData[THROTTLE] < BREAKPOINT) {
prop2 = 100;
} else {
if (rcData[THROTTLE] < 2000) {
prop2 = 100 - (uint16_t) cfg.dynThrPID * (rcData[THROTTLE] - BREAKPOINT) / (2000 - BREAKPOINT);
} else {
prop2 = 100 - cfg.dynThrPID;
}
}
for (axis = 0; axis < 3; axis++) {
tmp = min(abs(rcData[axis] - cfg.midrc), 500);
if (axis != 2) { // ROLL & PITCH
if (cfg.deadband) {
if (tmp > cfg.deadband) {
tmp -= cfg.deadband;
} else {
tmp = 0;
}
}
tmp2 = tmp / 100;
rcCommand[axis] = lookupPitchRollRC[tmp2] + (tmp - tmp2 * 100) * (lookupPitchRollRC[tmp2 + 1] - lookupPitchRollRC[tmp2]) / 100;
prop1 = 100 - (uint16_t) cfg.rollPitchRate * tmp / 500;
prop1 = (uint16_t) prop1 *prop2 / 100;
} else { // YAW
if (cfg.yawdeadband) {
if (tmp > cfg.yawdeadband) {
tmp -= cfg.yawdeadband;
} else {
tmp = 0;
}
}
rcCommand[axis] = tmp;
prop1 = 100 - (uint16_t) cfg.yawRate * tmp / 500;
}
dynP8[axis] = (uint16_t) cfg.P8[axis] * prop1 / 100;
dynD8[axis] = (uint16_t) cfg.D8[axis] * prop1 / 100;
if (rcData[axis] < cfg.midrc)
rcCommand[axis] = -rcCommand[axis];
}
tmp = constrain(rcData[THROTTLE], cfg.mincheck, 2000);
tmp = (uint32_t) (tmp - cfg.mincheck) * 1000 / (2000 - cfg.mincheck); // [MINCHECK;2000] -> [0;1000]
tmp2 = tmp / 100;
rcCommand[THROTTLE] = lookupThrottleRC[tmp2] + (tmp - tmp2 * 100) * (lookupThrottleRC[tmp2 + 1] - lookupThrottleRC[tmp2]) / 100; // [0;1000] -> expo -> [MINTHROTTLE;MAXTHROTTLE]
if(f.HEADFREE_MODE) {
float radDiff = (heading - headFreeModeHold) * M_PI / 180.0f;
float cosDiff = cosf(radDiff);
float sinDiff = sinf(radDiff);
int16_t rcCommand_PITCH = rcCommand[PITCH] * cosDiff + rcCommand[ROLL] * sinDiff;
rcCommand[ROLL] = rcCommand[ROLL] * cosDiff - rcCommand[PITCH] * sinDiff;
rcCommand[PITCH] = rcCommand_PITCH;
}
if (feature(FEATURE_VBAT)) {
if (!(++vbatTimer % VBATFREQ)) {
vbatRawArray[(ind++) % 8] = adcGetBattery();
for (i = 0; i < 8; i++)
vbatRaw += vbatRawArray[i];
vbat = batteryAdcToVoltage(vbatRaw / 8);
}
if ((vbat > batteryWarningVoltage) || (vbat < cfg.vbatmincellvoltage)) { // VBAT ok, buzzer off
buzzerFreq = 0;
} else
buzzerFreq = 4; // low battery
}
buzzer(buzzerFreq); // external buzzer routine that handles buzzer events globally now
if ((calibratingA > 0 && sensors(SENSOR_ACC)) || (calibratingG > 0)) { // Calibration phasis
LED0_TOGGLE;
} else {
if (f.ACC_CALIBRATED)
LED0_OFF;
if (f.ARMED)
LED0_ON;
// This will switch to/from 9600 or 115200 baud depending on state. Of course, it should only do it on changes.
if (feature(FEATURE_TELEMETRY))
initTelemetry(f.ARMED);
}
#ifdef LEDRING
if (feature(FEATURE_LED_RING)) {
static uint32_t LEDTime;
if ((int32_t)(currentTime - LEDTime) >= 0) {
LEDTime = currentTime + 50000;
ledringState();
}
}
#endif
if ((int32_t)(currentTime - calibratedAccTime) >= 0) {
if (!f.SMALL_ANGLES_25) {
f.ACC_CALIBRATED = 0; // the multi uses ACC and is not calibrated or is too much inclinated
LED0_TOGGLE;
calibratedAccTime = currentTime + 500000;
} else {
f.ACC_CALIBRATED = 1;
}
}
serialCom();
if (sensors(SENSOR_GPS)) {
static uint32_t GPSLEDTime;
if ((int32_t)(currentTime - GPSLEDTime) >= 0 && (GPS_numSat >= 5)) {
GPSLEDTime = currentTime + 150000;
LED1_TOGGLE;
}
}
// Read out gyro temperature. can use it for something somewhere. maybe get MCU temperature instead? lots of fun possibilities.
if (gyro.temperature)
gyro.temperature(&telemTemperature1);
else {
// TODO MCU temp
}
}
uint16_t pwmReadRawRC(uint8_t chan)
{
uint16_t data;
data = pwmRead(cfg.rcmap[chan]);
if (data < 750 || data > 2250)
data = cfg.midrc;
return data;
}
void computeRC(void)
{
static int16_t rcData4Values[8][4], rcDataMean[8];
static uint8_t rc4ValuesIndex = 0;
uint8_t chan, a;
rc4ValuesIndex++;
for (chan = 0; chan < 8; chan++) {
rcData4Values[chan][rc4ValuesIndex % 4] = rcReadRawFunc(chan);
rcDataMean[chan] = 0;
for (a = 0; a < 4; a++)
rcDataMean[chan] += rcData4Values[chan][a];
rcDataMean[chan] = (rcDataMean[chan] + 2) / 4;
if (rcDataMean[chan] < rcData[chan] - 3)
rcData[chan] = rcDataMean[chan] + 2;
if (rcDataMean[chan] > rcData[chan] + 3)
rcData[chan] = rcDataMean[chan] - 2;
}
}
void loop(void)
{
static uint8_t rcDelayCommand; // this indicates the number of time (multiple of RC measurement at 50Hz) the sticks must be maintained to run or switch off motors
uint8_t axis, i;
int16_t error, errorAngle;
int16_t delta, deltaSum;
int16_t PTerm, ITerm, PTermACC, ITermACC = 0, PTermGYRO = 0, ITermGYRO = 0, DTerm;
static int16_t lastGyro[3] = { 0, 0, 0 };
static int16_t delta1[3], delta2[3];
static int16_t errorGyroI[3] = { 0, 0, 0 };
static int16_t errorAngleI[2] = { 0, 0 };
static uint32_t rcTime = 0;
static int16_t initialThrottleHold;
static uint32_t loopTime;
uint16_t auxState = 0;
int16_t prop;
// this will return false if spektrum is disabled. shrug.
if (spektrumFrameComplete())
computeRC();
if ((int32_t)(currentTime - rcTime) >= 0) { // 50Hz
rcTime = currentTime + 20000;
// TODO clean this up. computeRC should handle this check
if (!feature(FEATURE_SPEKTRUM))
computeRC();
// Failsafe routine
if (feature(FEATURE_FAILSAFE)) {
if (failsafeCnt > (5 * cfg.failsafe_delay) && f.ARMED) { // Stabilize, and set Throttle to specified level
for (i = 0; i < 3; i++)
rcData[i] = cfg.midrc; // after specified guard time after RC signal is lost (in 0.1sec)
rcData[THROTTLE] = cfg.failsafe_throttle;
if (failsafeCnt > 5 * (cfg.failsafe_delay + cfg.failsafe_off_delay)) { // Turn OFF motors after specified Time (in 0.1sec)
f.ARMED = 0; // This will prevent the copter to automatically rearm if failsafe shuts it down and prevents
f.OK_TO_ARM = 0; // to restart accidentely by just reconnect to the tx - you will have to switch off first to rearm
}
failsafeEvents++;
}
if (failsafeCnt > (5 * cfg.failsafe_delay) && !f.ARMED) { // Turn off "Ok To arm to prevent the motors from spinning after repowering the RX with low throttle and aux to arm
f.ARMED = 0; // This will prevent the copter to automatically rearm if failsafe shuts it down and prevents
f.OK_TO_ARM = 0; // to restart accidentely by just reconnect to the tx - you will have to switch off first to rearm
}
failsafeCnt++;
}
if (rcData[THROTTLE] < cfg.mincheck) {
errorGyroI[ROLL] = 0;
errorGyroI[PITCH] = 0;
errorGyroI[YAW] = 0;
errorAngleI[ROLL] = 0;
errorAngleI[PITCH] = 0;
rcDelayCommand++;
if (rcData[YAW] < cfg.mincheck && rcData[PITCH] < cfg.mincheck && !f.ARMED) {
if (rcDelayCommand == 20) {
calibratingG = 1000;
if (feature(FEATURE_GPS))
GPS_reset_home_position();
}
} else if (feature(FEATURE_INFLIGHT_ACC_CAL) && (!f.ARMED && rcData[YAW] < cfg.mincheck && rcData[PITCH] > cfg.maxcheck && rcData[ROLL] > cfg.maxcheck)) {
if (rcDelayCommand == 20) {
if (AccInflightCalibrationMeasurementDone) { // trigger saving into eeprom after landing
AccInflightCalibrationMeasurementDone = 0;
AccInflightCalibrationSavetoEEProm = 1;
} else {
AccInflightCalibrationArmed = !AccInflightCalibrationArmed;
if (AccInflightCalibrationArmed) {
toggleBeep = 2;
} else {
toggleBeep = 3;
}
}
}
} else if (cfg.activate[BOXARM] > 0) {
if (rcOptions[BOXARM] && f.OK_TO_ARM) {
// TODO: feature(FEATURE_FAILSAFE) && failsafeCnt == 0
f.ARMED = 1;
headFreeModeHold = heading;
} else if (f.ARMED)
f.ARMED = 0;
rcDelayCommand = 0;
} else if ((rcData[YAW] < cfg.mincheck || (cfg.retarded_arm == 1 && rcData[ROLL] < cfg.mincheck)) && f.ARMED) {
if (rcDelayCommand == 20)
f.ARMED = 0; // rcDelayCommand = 20 => 20x20ms = 0.4s = time to wait for a specific RC command to be acknowledged
} else if ((rcData[YAW] > cfg.maxcheck || (rcData[ROLL] > cfg.maxcheck && cfg.retarded_arm == 1)) && rcData[PITCH] < cfg.maxcheck && !f.ARMED && calibratingG == 0 && f.ACC_CALIBRATED) {
if (rcDelayCommand == 20) {
f.ARMED = 1;
headFreeModeHold = heading;
}
} else
rcDelayCommand = 0;
} else if (rcData[THROTTLE] > cfg.maxcheck && !f.ARMED) {
if (rcData[YAW] < cfg.mincheck && rcData[PITCH] < cfg.mincheck) { // throttle=max, yaw=left, pitch=min
if (rcDelayCommand == 20)
calibratingA = 400;
rcDelayCommand++;
} else if (rcData[YAW] > cfg.maxcheck && rcData[PITCH] < cfg.mincheck) { // throttle=max, yaw=right, pitch=min
if (rcDelayCommand == 20)
f.CALIBRATE_MAG = 1; // MAG calibration request
rcDelayCommand++;
} else if (rcData[PITCH] > cfg.maxcheck) {
cfg.angleTrim[PITCH] += 2;
writeParams(1);
#ifdef LEDRING
if (feature(FEATURE_LED_RING))
ledringBlink();
#endif
} else if (rcData[PITCH] < cfg.mincheck) {
cfg.angleTrim[PITCH] -= 2;
writeParams(1);
#ifdef LEDRING
if (feature(FEATURE_LED_RING))
ledringBlink();
#endif
} else if (rcData[ROLL] > cfg.maxcheck) {
cfg.angleTrim[ROLL] += 2;
writeParams(1);
#ifdef LEDRING
if (feature(FEATURE_LED_RING))
ledringBlink();
#endif
} else if (rcData[ROLL] < cfg.mincheck) {
cfg.angleTrim[ROLL] -= 2;
writeParams(1);
#ifdef LEDRING
if (feature(FEATURE_LED_RING))
ledringBlink();
#endif
} else {
rcDelayCommand = 0;
}
}
if (feature(FEATURE_INFLIGHT_ACC_CAL)) {
if (AccInflightCalibrationArmed && f.ARMED && rcData[THROTTLE] > cfg.mincheck && !rcOptions[BOXARM]) { // Copter is airborne and you are turning it off via boxarm : start measurement
InflightcalibratingA = 50;
AccInflightCalibrationArmed = 0;
}
if (rcOptions[BOXPASSTHRU]) { // Use the Passthru Option to activate : Passthru = TRUE Meausrement started, Land and passtrhu = 0 measurement stored
if (!AccInflightCalibrationActive && !AccInflightCalibrationMeasurementDone)
InflightcalibratingA = 50;
} else if (AccInflightCalibrationMeasurementDone && !f.ARMED) {
AccInflightCalibrationMeasurementDone = 0;
AccInflightCalibrationSavetoEEProm = 1;
}
}
for(i = 0; i < 4; i++)
auxState |= (rcData[AUX1 + i] < 1300) << (3 * i) | (1300 < rcData[AUX1 + i] && rcData[AUX1 + i] < 1700) << (3 * i + 1) | (rcData[AUX1 + i] > 1700) << (3 * i + 2);
for(i = 0; i < CHECKBOXITEMS; i++)
rcOptions[i] = (auxState & cfg.activate[i]) > 0;
// note: if FAILSAFE is disable, failsafeCnt > 5*FAILSAVE_DELAY is always false
if ((rcOptions[BOXANGLE] || (failsafeCnt > 5 * cfg.failsafe_delay)) && (sensors(SENSOR_ACC))) {
// bumpless transfer to Level mode
if (!f.ANGLE_MODE) {
errorAngleI[ROLL] = 0;
errorAngleI[PITCH] = 0;
f.ANGLE_MODE = 1;
}
} else {
f.ANGLE_MODE = 0; // failsave support
}
if (rcOptions[BOXHORIZON]) {
if (!f.HORIZON_MODE) {
errorAngleI[ROLL] = 0;
errorAngleI[PITCH] = 0;
f.HORIZON_MODE = 1;
}
} else {
f.HORIZON_MODE = 0;
}
if ((rcOptions[BOXARM]) == 0)
f.OK_TO_ARM = 1;
if (f.ANGLE_MODE || f.HORIZON_MODE) {
LED1_ON;
} else {
LED1_OFF;
}
#ifdef BARO
if (sensors(SENSOR_BARO)) {
if (rcOptions[BOXBARO]) {
if (!f.BARO_MODE) {
f.BARO_MODE = 1;
AltHold = EstAlt;
initialThrottleHold = rcCommand[THROTTLE];
errorAltitudeI = 0;
BaroPID = 0;
}
} else
f.BARO_MODE = 0;
}
#endif
#ifdef MAG
if (sensors(SENSOR_MAG)) {
if (rcOptions[BOXMAG]) {
if (!f.MAG_MODE) {
f.MAG_MODE = 1;
magHold = heading;
}
} else
f.MAG_MODE = 0;
if (rcOptions[BOXHEADFREE]) {
if (!f.HEADFREE_MODE) {
f.HEADFREE_MODE = 1;
}
} else {
f.HEADFREE_MODE = 0;
}
if (rcOptions[BOXHEADADJ]) {
headFreeModeHold = heading; // acquire new heading
}
}
#endif
if (sensors(SENSOR_GPS)) {
if (f.GPS_FIX && GPS_numSat >= 5) {
if (rcOptions[BOXGPSHOME]) {
if (!f.GPS_HOME_MODE) {
f.GPS_HOME_MODE = 1;
GPS_set_next_wp(&GPS_home[LAT], &GPS_home[LON]);
nav_mode = NAV_MODE_WP;
}
} else {
f.GPS_HOME_MODE = 0;
}
if (rcOptions[BOXGPSHOLD]) {
if (!f.GPS_HOLD_MODE) {
f.GPS_HOLD_MODE = 1;
GPS_hold[LAT] = GPS_coord[LAT];
GPS_hold[LON] = GPS_coord[LON];
GPS_set_next_wp(&GPS_hold[LAT], &GPS_hold[LON]);
nav_mode = NAV_MODE_POSHOLD;
}
} else {
f.GPS_HOLD_MODE = 0;
}
}
}
if (rcOptions[BOXPASSTHRU]) {
f.PASSTHRU_MODE = 1;
} else {
f.PASSTHRU_MODE = 0;
}
if (cfg.mixerConfiguration == MULTITYPE_FLYING_WING || cfg.mixerConfiguration == MULTITYPE_AIRPLANE) {
f.HEADFREE_MODE = 0;
}
} else { // not in rc loop
static int8_t taskOrder = 0; // never call all function in the same loop, to avoid high delay spikes
switch (taskOrder++ % 4) {
case 0:
#ifdef MAG
if (sensors(SENSOR_MAG))
Mag_getADC();
#endif
break;
case 1:
#ifdef BARO
if (sensors(SENSOR_BARO))
Baro_update();
#endif
break;
case 2:
#ifdef BARO
if (sensors(SENSOR_BARO))
getEstimatedAltitude();
#endif
break;
case 3:
#ifdef SONAR
if (sensors(SENSOR_SONAR)) {
Sonar_update();
debug[2] = sonarAlt;
}
#endif
break;
default:
taskOrder = 0;
break;
}
}
currentTime = micros();
if (cfg.looptime == 0 || (int32_t)(currentTime - loopTime) >= 0) {
loopTime = currentTime + cfg.looptime;
computeIMU();
// Measure loop rate just afer reading the sensors
currentTime = micros();
cycleTime = (int32_t)(currentTime - previousTime);
previousTime = currentTime;
#ifdef MPU6050_DMP
mpu6050DmpLoop();
#endif
#ifdef MAG
if (sensors(SENSOR_MAG)) {
if (abs(rcCommand[YAW]) < 70 && f.MAG_MODE) {
int16_t dif = heading - magHold;
if (dif <= -180)
dif += 360;
if (dif >= +180)
dif -= 360;
if (f.SMALL_ANGLES_25)
rcCommand[YAW] -= dif * cfg.P8[PIDMAG] / 30; // 18 deg
} else
magHold = heading;
}
#endif
#ifdef BARO
if (sensors(SENSOR_BARO)) {
if (f.BARO_MODE) {
if (abs(rcCommand[THROTTLE] - initialThrottleHold) > cfg.alt_hold_throttle_neutral) {
f.BARO_MODE = 0; // so that a new althold reference is defined
}
rcCommand[THROTTLE] = initialThrottleHold + BaroPID;
}
}
#endif
if (sensors(SENSOR_GPS)) {
// Check that we really need to navigate ?
if ((!f.GPS_HOME_MODE && !f.GPS_HOLD_MODE) || !f.GPS_FIX_HOME) {
// If not. Reset nav loops and all nav related parameters
GPS_reset_nav();
} else {
float sin_yaw_y = sinf(heading * 0.0174532925f);
float cos_yaw_x = cosf(heading * 0.0174532925f);
if (cfg.nav_slew_rate) {
nav_rated[LON] += constrain(wrap_18000(nav[LON] - nav_rated[LON]), -cfg.nav_slew_rate, cfg.nav_slew_rate); // TODO check this on uint8
nav_rated[LAT] += constrain(wrap_18000(nav[LAT] - nav_rated[LAT]), -cfg.nav_slew_rate, cfg.nav_slew_rate);
GPS_angle[ROLL] = (nav_rated[LON] * cos_yaw_x - nav_rated[LAT] * sin_yaw_y) / 10;
GPS_angle[PITCH] = (nav_rated[LON] * sin_yaw_y + nav_rated[LAT] * cos_yaw_x) / 10;
} else {
GPS_angle[ROLL] = (nav[LON] * cos_yaw_x - nav[LAT] * sin_yaw_y) / 10;
GPS_angle[PITCH] = (nav[LON] * sin_yaw_y + nav[LAT] * cos_yaw_x) / 10;
}
}
}
// **** PITCH & ROLL & YAW PID ****
prop = max(abs(rcCommand[PITCH]), abs(rcCommand[ROLL])); // range [0;500]
for (axis = 0; axis < 3; axis++) {
if ((f.ANGLE_MODE || f.HORIZON_MODE) && axis < 2) { // MODE relying on ACC
// 50 degrees max inclination
errorAngle = constrain(2 * rcCommand[axis] + GPS_angle[axis], -500, +500) - angle[axis] + cfg.angleTrim[axis];
#ifdef LEVEL_PDF
PTermACC = -(int32_t)angle[axis] * cfg.P8[PIDLEVEL] / 100;
#else
PTermACC = (int32_t)errorAngle * cfg.P8[PIDLEVEL] / 100; // 32 bits is needed for calculation: errorAngle*P8[PIDLEVEL] could exceed 32768 16 bits is ok for result
#endif
PTermACC = constrain(PTermACC, -cfg.D8[PIDLEVEL] * 5, +cfg.D8[PIDLEVEL] * 5);
errorAngleI[axis] = constrain(errorAngleI[axis] + errorAngle, -10000, +10000); // WindUp
ITermACC = ((int32_t)errorAngleI[axis] * cfg.I8[PIDLEVEL]) >> 12;
}
if (!f.ANGLE_MODE || axis == 2) { // MODE relying on GYRO or YAW axis
error = (int32_t)rcCommand[axis] * 10 * 8 / cfg.P8[axis];
error -= gyroData[axis];
PTermGYRO = rcCommand[axis];
errorGyroI[axis] = constrain(errorGyroI[axis] + error, -16000, +16000); // WindUp
if (abs(gyroData[axis]) > 640)
errorGyroI[axis] = 0;
ITermGYRO = (errorGyroI[axis] / 125 * cfg.I8[axis]) >> 6;
}
if (f.HORIZON_MODE && axis < 2) {
PTerm = ((int32_t)PTermACC * (500 - prop) + (int32_t)PTermGYRO * prop) / 500;
ITerm = ((int32_t)ITermACC * (500 - prop) + (int32_t)ITermGYRO * prop) / 500;
} else {
if (f.ANGLE_MODE && axis < 2) {
PTerm = PTermACC;
ITerm = ITermACC;
} else {
PTerm = PTermGYRO;
ITerm = ITermGYRO;
}
}
PTerm -= (int32_t)gyroData[axis] * dynP8[axis] / 10 / 8; // 32 bits is needed for calculation
delta = gyroData[axis] - lastGyro[axis]; // 16 bits is ok here, the dif between 2 consecutive gyro reads is limited to 800
lastGyro[axis] = gyroData[axis];
deltaSum = delta1[axis] + delta2[axis] + delta;
delta2[axis] = delta1[axis];
delta1[axis] = delta;
DTerm = ((int32_t)deltaSum * dynD8[axis]) >> 5; // 32 bits is needed for calculation
axisPID[axis] = PTerm + ITerm - DTerm;
}
mixTable();
writeServos();
writeMotors();
}
}
Reference in a new issue View git blame Copy permalink