Previous logic was always registering CRSL and SRXL as CMS displayPort devices regardless of whether the user was actually using that type of radio and telemetry.
The problem this caused is that if the user accidentally (or intentionally) used the CMS invoke stick command while already in the CMS on the MAX7456 the logic interprets this to mean "switch to the next registered displayPort device". So in this case the CMS would appear to exit based on what the user could see. But in reality it's still active and simply switched to the next (nonexistent) device. The user is then stuck and can't arm because the `CMS` arming disabled will be active and they have no way to interact with the CMS. They can technically blindly do the CMS stick command 2 more times to get back to the MAX7456, but how would they know that?
So this change only registers the CRSF and SRXL displayPorts when the user has selected those receiver types and enabled telemetry.
This is actually only a partial solution since it prevents registering the devices when they're impossible to work, but doesn't do anything for the actual CRSF or SRXL user that may be using equipment not capable of displaying the CMS. So it's still possible for them to get stuck in this situation. But I don't see any reasonable way to prevent this.
Perhaps it's time to rethink this "Switch to next CMS device" logic? It's something that nobody really knows about and seems to be more trouble than value. Maybe there are some edge cases where it's useful like using the OLED dashboard along with a MAX7456, but that's a rare use-case. Or possibly we need some explicit control where the user has to enable the particular displayPort device to be eligible for CMS?
Improve the logic to be table-based and add validation of the rc_rates and expo values. The previous logic only validated the super-rates and the rc_rates can also be out-of-range when changing rates types. The expo values are also checked but currently all the rates types have the same constraints so there's no possibility currently of them being out of range. But this will allow for possible new rates type that have different constraints.
Since version 4.0.0 CLI variables:
* acc_cut_hz,
* accxy_deadband,
* accz_deadband,
* acc_unarmedcal
are removed from settings.c and thus can be also removed
from the CLI documentation page.
Fixes logic errors in #9574
For RACEFLIGHT rates the applicable `case` was missing so the logic defaulted to the BETAFLIGHT rates logic which incorrectly limited the maximum rate value to 100. RACEFLIGHT values range to 255.
For KISS rates the limit was set to 100 but the Configurator constrains to 99.
Changes the blink logic to be OSD task loop based instead of time based.
The previous logic used a 200ms time interval for the blinking which didn't align well with the default 12hz OSD update frequency resulting in the logic periodically missing intervals resulting in an inconsistent blinking.
As the revised logic is now tied to the OSD task iterations the blinking will be consistent. However due to the timing the blink will be slightly faster - 167ms (6hz) vs. the previous 200ms (5hz) intervals. Technically the blinking was 6hz before but stuttered every 5th blink.
Since the OSD task rate can be changed from the default 60hz, the logic will fall back to the time-based implementation for non-default task rates.
Ensure DMA_RAM section is at start of RAM and the the region defining the shareable region is covered.
Enable USE_LEDSTRIP_CACHE_MGMT on NUCLEOH743 target
Add ability for pilots to log CRC errors, unknown frames, LQ, and RSSI.
Added macro to debug.h to simplify incrementing debug values without the need for local statics in client code.
Fix the issue described in Issue #10220, typos in serial drivers for F7, F3, G4, H7 platforms.
Before this change, the serial line is incorrectly pulled down for bidirectional comms, which may cause dropped packets (silently) with any Rx protocol that uses bidirectional comms on the Tx line (GHST, SRXL-2, FPORT)
