- Including ability to define custom defaults as char[] that is baked into the build
- removed unnecessary size of custom defaults header parsing (defines provided by build process or in board.h for devs).
- Updating cache for tool chain
- Using 10.3 as the build chain, due to bug in 11.2 -> https://bugs.linaro.org/show_bug.cgi?id=5825.
- No inlining to prevent over flow. Perhaps other calls represent better choices.
The H730 is a value-line CPU, similar to the H723/H725, but with only
128kb RAM.
The FC firmware code is designed to RUN from external flash in MEMORY
MAPPED mode, via OctoSPI. Use of ITCM/DTCM advised for core loops, like
PID control.
A bootloader is required to enable memory-mapped mode and jump to the
firmware, similar to how EXST bootloader system works.
Config storage is not part of this commit and is a problem when using a
single flash chip in memory mapped mode because the CPU can't run
read/write routines from the flash chip while writing to the flash chip.
Until flash read/write routines are updated the solution requires either
a second flash chip on an SPI interface, or the use of an SD card for
config storage.
Additional commits will support read/write of config to the code/data
storage flash chip to enable cheap and space efficient single-flash-chip
FC solutions.
Squashed commits:
STM32H730 - Workaround issue with 2GB `.elf` files being created.
STM32H730 - Reduce firmware size to 1MB.
STM32H730 - Add USB HS configuration.
STM32H730 - Add ADC internal tag mappings.
STM32H730 - Update all ADC mappings based on the referenced ST
documentation. Add the VBAT channels.
STM32H730 - Fix DMA continuous requests.
STM32H730 - Fix ADC_INTERNAL confusion.
STM32H730/G4 - Disambiguate use of ADC_CHANNEL_INTERNAL_FIRST_ID.
STM32H730 - Fix documentation reference.
STM32H730 - Add DMA request mapping for ADC3.
STM32H730 - Explicitly set the ADC clock.
STM32H730 - Configure PLL2 speeds correctly.
* Tested with Ultrafast 64GB SanDisk SDXC card.
STM32H730 - Use 50Mhz clock for SDXC cards.
* Tested with SanDisk Ultra 64GB. 100Mhz clock gave CRC errors.
STM32H730 - Ensure USB has a lower NVIC priority than the SDMMC card
reads.
If it's higher, 0, then the SDMMC's DMA IRQ handler doesn't get called
when handing USB MSC storage reads.
STM32H730 - Support CPU name in CLI.
STM32H730 - Rebuild when linker scripts changes.
Call targetConfiguration() once before config is loaded and again afterwards in case the config needs to be changed to load from SD card etc
Drop SPI clock during binding
Remove debug
Add per device SPI DMA enable
Fix sdioPinConfigure() declaration warning
Reduce clock speed during SPI RX initialisation
* Enable QSPI flash chip drivers on NUCLEOH743 for some CI visibility.
* Rework QSPI flash detection.
* Supports chips that are in QSPI mode by default (factory).
* Supports chips that are in QSPI mode due to configuration (e.g. Quad
Enable in Non-Volatile on W25Q128FV)
* Supports chips that need 8 dummy bytes (e.g. W25Q128JV) and ones that
don't (e.g. W25N01G)
Adds variations in GPS coordinate OSD element display:
1. Fractional degrees with 7 digits (default) - 000.0000000
2. Fractional degrees with 4 digits - 000.0000
3. Degrees, minutes, seconds - 000^00'00.0"E
4. Open Location Code (sometimed called Google Plus Code) - 23ABC4R8+M37
Uses Open Location Code library from:
https://github.com/google/open-location-code
Added support for `STATE(GPS_FIX_EVER)` to differentiate from having a fix now (`STATE(GPS_FIX)`) vs. ever having a fix.
Logic change to only display coordinates from the GPS module once a fix has been initially established. This prevents displaying interim coordinates supplied by the GPS while the fix is still being establised as these coordinates can be inaccurate by hundreds of miles. Once a fix is established initially then the coordinates will continue to be displayed even if the fix is lost or degrades in quality.
Add logic to "blink" the coordinates if the 3D fix is lost after initially being established. Alerts the user that the coordinate display may be inaccurate or no longer being updated. We want to keep the coordinates displayed to aid recovery if the user loses the fix (like crashing upside down).
Replace GPS defines `LAT` and `LON` used throughout the code with the enumeration:
```
typedef enum {
GPS_LATITUDE,
GPS_LONGITUDE
} gpsCoordinateType_e;
```
The Open Location Code option is bounded with `USE_GPS_PLUS_CODE` to allow it to be excluded if needed for targets with limited flash space. It currently fits for F411 but we may have to remove it in the future.
Provides a properly implemented way for MSP query type OSD implementations (like DJI) to display OSD warnings. Separates the warnings generation from the OSD task and shares common code to make the text available for the OSD and/or via MSP. Eliminates the need to implement hacks and workarounds like using the `CRAFT_NAME` field to display warnings. Since the warnings logic is now separate, the OSD task does not need to be running unlike other hacks.
Adds the `MSP2_GET_OSD_WARNINGS` message formatted as follows:
```
byte description
0 Display attributes including blink (see displayPortAttr_e in drivers/display.h)
1 Length of warning text
2-n Warning text characters
```
